Recent content by low_psi

After some research, active adapters are needed and all I found would only get to 120hz and were very expensive. Took the monitors back and bought 3 Asus 144hz monitors with dp ports.

I have a Zotac AMP Extreme GTX 980 ti. It has one DVI-D dual output and 3 DP outputs. I have three Acer GN246HL 144hz monitors. These monitors only have VGA and DVI-D Dual inputs. Using the DVI-D output on the card directly to one of the monitor works and results in 144hz signal. I have a...

My new 980ti will be delivered tomorrow. This 980 is ready to ship. I am open to reasonable offers....

SOLD I have a Gigabyte G1 Gaming GTX980 4GB in excellent condition. It is only 3 months old and has seen very light use in a smoke free home. I am an IT professional (over 15 yrs) so you can be assured it has been handled properly since new. This card has performed flawlessly for me in a...

The Intel drivers are new as of yesterday. Up until yesterday, I had the onboard disabled and had never installed the drivers. Only enable after I added the fourth monitor..

I added a pic of the r9 details, it shows the same as the Intel. This is what has me confused. There is a noticeable performance increase when I disable the onboard video card in the BIOS. All the stuttering disappears in iracing. As soon as I enable the onboard video again (with our without...

Quick breakdown of the PC: Intel i5 4690k (clocked at 4.5 Ghz) Corsair H60 Cooler Gigabyte Z97X Gaming7 G Skill Sniper 2 x 4GB 1833 DDR3 EVGA SuperNova 850 watt XFX R9-290 Black Edition 3 Samsung S24D590pl Monitors 1 Samsung SyncMaster 205BW On to the issue.... I am using the 3 Samsung 24"...

I basically tried everything under the sun, including talking the buyer thru reinstalling Windows. Issue resurfaced within 30 seconds while running Valley Benchmark. Had him send me the Sapphire R9-280 video card. Put it in my newly built rig, and crashed on the first attempt running Valley...

I tried to help this kid buy offering him a brand new assembled, OC'd, Benchmarked, FX6300/MSI R9-270x/8GB RAM/1TB HD/600w EVGA PSU/Hyper 212 EVO Cooler/Win 7 64bit Pro/ for $610 shipped. And was called untrust worthy, told he could build it cheaper and better. But then asked me for a list of...

Well the problems have somewhat resurfaced... Now the PC seems to be crashing in iRacing only. He has run Furmark numerous times without any issues. I have instructed him to run the Valley Benchmark test as that seems to put the GPU under a much better load. I am thinking the problems may be...

I see the artifacts when remoted in... However, I had him unplug his monitor from the HDMi port and then I ran Furmark 4 times in a row and saw no artifacts on my screen (remote connection). While I find it hard to believe that his monitor could be effecting what I see remotely, I guess at...

I sold my 3 month old system to a guy last week. I have run this PC with iRacing for the three months with no issues @ 1080p resolution. Before I shipped it out I loaded Windows 7 64bit Pro on a new 2TB Hard Drive as I did not sell the machine with my SSD. I have loaded Windows a thousand...

It is definitely the power limit setting. I was able to crank it up using CCC. However using afterburner just isn't working... Increasing the power limit slider doesn't seem to change anything inside of msi afterburner.. I can crank things up in CCC and it test out better. Any ideas? I...

So my r9-280x was running at a voltage of 1.150 during the fur mark test. The r9-290 is only 1.04 during fur mark.........