Recent content by NiveusT

So, We've had a Nighthawk c7800 for cable for the past 2ish years or so. Recently we moved, and we got Fiber hooked up. The fiber goes into the house and into a hub that distributes it to whatever we have. Problem is, there's no WAN ethernet input for the C7800, just a coax. So we gotta use...

If it comes down to that- I will do that. But out of curiosity, in all of these tests- If it is the router, basically it comes down to replacing the router possibly, or adjusting the settings somehow and see if it fixes, right? If it is NOT the router... Is it likely to be a driver...

UPDATE: I will start semi-fresh and reiterate the problems, but just in case all of the above info is relevant I will leave it here. My current setup: ISP >COAX> Router/Modem Combo (Netgear Nighthawk C7800) >wire> GS305E – 5-Port Gigabit Ethernet Smart Managed Plus Switch >wire> Windows 11 PC...

Your diagram of my network is correct. Yeah, it works fine from wall jack to my PC. I did try the WAN and LAN ports on the WAX206 and they both do the dropping :( I only have one WAX206 AP. :< Yeah! I actually just bought a switch today LOL... Ugh. I'm sad the AP isn't working as intended...

All of this is happening on a wired connection thru the WAX206. Internet > Router (C7800) > AP (WAX206) > PC - All wired. This is when there are problems. The PC is my main concern because it's the one I game on as well as do zoom calls/meetings/etc on (wired). The wireless devices/wi-fi isn't a...

Yeah, I only noticed it because in the games I play (CS2, and Rainbow6 Siege, and a bit of Valorant) in the corners of the screen it will say "packet loss" or "connection problems" and show a download/upload red number that tells you what's happening, and I get super rubber banding. But it's on...

So, I'm fairly certain it's the AP at this point. I did the ipconfig /all during the drop outs. Everything shows up fine and not disconnected. Ipv6 was already disabled from my PC apparently from the start. I did the constant ping to 8.8.8.8 with cmd prompt "ping -t 8.8.8.8" - There are no...

I had a semi eureka moment... I think it's my access point (the WAX206). I connected directly to the MAIN router with my PC, and I had no problems at all. (I know I should have done this sooner but everyone is always using it so I stayed up late one night to check.) I plugged it back into the...

This is my router's mac address. I had 3 techs come out, adjust things on their wires etc. And still the issue persists. How can I tell them that it's the provisioning of the router in a way that will get them to check these things? They always just want to send out a tech with whatever I say...

We had some techs come out and double check all the cables and coax and things. The ISP checked the pole and said something was wrong with the pole and they'd get someone out to check the pole. However- I do not trust the ISP to know if that's the final issue. Here are the errors that show up...

Having a similar issue. Following this post. I think his .dmp file above is shared properly now. :)

That is the correct modem/router. That is the correct access point. That was until the Ring was installed. However- I do not know if the issue is directly related. I will be stopping their access to the network and see if the issue persists. I have verified that it is not the WAX206. It's the...

View: https://imgur.com/a/oITxHLe - < Network Structure. I have full admin rights, all of us can, at any time, change anything. All items have been identified. I see in the event log of the Router that it says this: 2024-06-09, 20:04:38 Critical (3) Started Unicast Maintenance Ranging - No...

I have Spectrum, 1G Download/60G Upload or something like that. Unlimited data, no caps. The coax goes into the wall to a Netgear C7800 on one side of the house. I have a Netgear WAX206 set up as an access point on the other side of the house. This is connected with an ethernet run outside...

Gotcha. I'll keep an eye out on it. I'm using Mine Craft's java version and it forces you to select an allocation of ram. It's installed straight from the mojang site. According to your instructions I should leave Mine Craft on when this problem happens? Will try to check out the resource...