Recent content by woolyone

Best answer selected by woolyone.

Now Solved!! With ought Doubt! 2 ways to make it fit. A: My way- Remove the heat sink lock down plate from the mother board. Only 2 screws hold that square plate down. Adjacent to where the bolt down screws are, cut, bevel, file out a half circular section. Try to make the same amount of cut...

Now SOLVED, Thank you. Still got no reply from Corsair. Used the stock standard heat sink plate that are on Asus 939 boards. Cut out circular section on both ends adjacent to where the 2 lock down screws screw onto the MB. Turn the heat sink plate upside down...

Thanks GOLgeek, Thanks for the reply. I was and am well aware of the difference in the mounting brackets, how they switched from 2 holes to 4. In the process of contacting an engineer who works a lot with aluminum. I tried to contact the corsair manufacturers by...

thanks outlw669. I could really "let rip" with the bloke who led me up the bloody garden parth with his reply to the contrary!!! IF you read my original post i "specifically asked about socket 939's " . if any one knew if there was an adaption plate available for...

Please help!! See my previous thread and answer posted here on Tom's below, which is no longer active so posting a new one: http://www.tomshardware.com/forum/ [...] eries-help In short, i am in dire straights. For the life of me i cannot see how i am going to mount this Corsair H70, CPU liquid...

Please help!! See my previous thread and answer posted here on Tom's below, which is no longer active so posting a new one: http://www.tomshardware.com/forum/300200-28-socket-adapter-corsair-hydro-series-help In short, i am in dire straights. For the life of me i cannot see how i am going to...

Not Solved!! Going on Endyen's reply INFORMATION i went ahead and purchased a Corsair H70 liqiud CPU Cooler. For the life of me i do not see how i can fit this to my ASUS A8N-SLI Premium motherboard!! SOCKET 939 . I was specific in the original post /question that it was for AN AMD SOCKET 939...

Back Again, I have done some checking and should be able to get one locally. Next thing is, has any one had the experience of fitting one of these Corsair Hydro H60's into a, Antec Nine Hundred Two Ultimate Gaming Case, which is what i have, picture via link below...

Thanks very much endyen. Thats great news for me, no doubt quite a few others who still love their Asus 939 Premium boards!! So if you are sure that with the mounting hardware supplied with the kit, it will definably bolt down on an Asus 939, i shall...

Hi All, Soled At Last!, endyen! I have an Asus A8N-SLI Premium motherboard, only been in service 2 years. The CPU is AMD Athlon X62 4600 Dual Core. I live in Queensland Australia and it gets really hot here!! The tower is an Antec 9200. This Liquid cooled heatsink setup featured on...

Hi again Bob, I can get ddr2 1gig sticks for about $35.00au. It ran from about 11.00am till about 3.30pm yesterday and did not go into shutdown before i actually shut it down. So itlooks promising but i'm not getting too exited just yet. It runs PCLInux no worries even with...

Hi Bob, Good to hear from you and very grateful for the reply. Sound like you know a bit about these old girls where as i am mostly an ASUS A8N GUY. Here is what i tried first off, disabled acpi, in power management i have 3 choices-user define(which i had it set to), min saving and...

Hi All, Have a similiar post about this under motherboards. Thought i might try in a more generalized area. Firstly basic specs: FOXCONN P4M800P7MA-RS2-Pentium 4 Dual Core-512mb ram- Nvidia FX128 AGP-Current System-PCLinux 2007. Bios- very complicated Phoenix Award V-6.00PG. This old...