Question ADATA SU655 at 100% usage and bad block errors spammed in Event Viewer ?

xray559

Commendable
Jan 2, 2020
65
1
1,535
0
My system drive (ADATA SU655) started to hit 100% randomly upon starting my computer, mostly when apps were starting up, running, etc. As a result, my computer's load speeds are extremely low and laggy. I checked the event viewer and found out that an error called "The device, \Device\Harddisk0\DR0, has a bad block." was being spammed in my system logs. I tried the error checking tool in the properties of my system drive, and it detected errors, restarted, and supposedly fixed the errors. After the Error check, my c drive is still hitting 100%, Windows is acting slow, etc. I've tried sfc/scannow, restarting, booting into safe mode, and checking my drive's health status on ADATA's toolbox. I'm currently at a loss and expect that my C Drive gave out after four years of usage. Help would be greatly appreciated.

Note: Coincidentally, this issue started after upgrading my corsair lpx ram to 32gb 3200mhz. I'm going to swap out my new ram for my old ram and run the same tests I did.


Computer: MSI MS-7B07
CPU: AMD Ryzen 5 2600 (Pinnacle Ridge, PiR-B2)
3400 MHz (34.00x100.0) @ 3773 MHz (37.75x100.0)
Motherboard: MSI A320M PRO-VH PLUS (MS-7B07)
BIOS: 3.I2, 05/10/2022
Chipset: AMD A320 (Promontory)
Memory: 32768 MBytes @ 1599 MHz, 16-20-20-38
- 16384 MB PC25600 DDR4 SDRAM - Corsair CMK32GX4M2E3200C16
- 16384 MB PC25600 DDR4 SDRAM - Corsair CMK32GX4M2E3200C16
Graphics: NVIDIA, Device ID: 2504 [PNY Technologies]
, 0 MB
Drive: ADATA SU655, 117.2 GB, Serial ATA 6Gb/s @ 6Gb/s
Drive: TOSHIBA HDWD110, 976.8 GB, Serial ATA 6Gb/s @ 6Gb/s
Drive: ADATA SU800, 500.1 GB, Serial ATA 6Gb/s @ 6Gb/s
Drive: Samsung SSD 870 EVO 1TB, 976.8 GB, Serial ATA 6Gb/s @ 6Gb/s
Drive: MSFT XVDD, Disk drive
OS: Microsoft Windows 10 Home (x64) Build 19044.1826
 
Last edited:
My system drive (ADATA SU655) started to hit 100% randomly upon starting my computer, mostly when apps were starting up, running, etc. As a result, my computer's load speeds are extremely low and laggy. I checked the event viewer and found out that an error called "The device, \Device\Harddisk0\DR0, has a bad block." was being spammed in my system logs. I tried the error checking tool in the properties of my system drive, and it detected errors, restarted, and supposedly fixed the errors. After the Error check, my c drive is still hitting 100%, Windows is acting slow, etc. I've tried sfc/scannow, restarting, booting into safe mode, and checking my drive's health status on ADATA's toolbox. I'm currently at a loss and expect that my C Drive gave out after four years of usage. Help would be greatly appreciated.

Note: Coincidentally, this issue started after upgrading my corsair lpx ram to 32gb 3200mhz. I'm going to swap out my new ram for my old ram and run the same tests I did.






Computer: MSI MS-7B07
CPU: AMD Ryzen 5 2600 (Pinnacle Ridge, PiR-B2)
3400 MHz (34.00x100.0) @ 3773 MHz (37.75x100.0)
Motherboard: MSI A320M PRO-VH PLUS (MS-7B07)
BIOS: 3.I2, 05/10/2022
Chipset: AMD A320 (Promontory)
Memory: 32768 MBytes @ 1599 MHz, 16-20-20-38
- 16384 MB PC25600 DDR4 SDRAM - Corsair CMK32GX4M2E3200C16
- 16384 MB PC25600 DDR4 SDRAM - Corsair CMK32GX4M2E3200C16
Graphics: NVIDIA, Device ID: 2504 [PNY Technologies]
, 0 MB
Drive: ADATA SU655, 117.2 GB, Serial ATA 6Gb/s @ 6Gb/s
Drive: TOSHIBA HDWD110, 976.8 GB, Serial ATA 6Gb/s @ 6Gb/s
Drive: ADATA SU800, 500.1 GB, Serial ATA 6Gb/s @ 6Gb/s
Drive: Samsung SSD 870 EVO 1TB, 976.8 GB, Serial ATA 6Gb/s @ 6Gb/s
Drive: MSFT XVDD, Disk drive
OS: Microsoft Windows 10 Home (x64) Build 19044.1826
would expect that out of adata budget ssds. lots friends of mine used the SU650 and got bad blocks like you in several months.
 

Maxxify

Distinguished
Check CrystalDiskInfo for drive errors/issues. While the SU650/SU655 is not a good drive, it's just as likely your memory had errors at its given speeds/timings (possibly IMC/board limitation) which corrupted data on the disk. You should always test when adding new memory - Prime95 cache can test IMC, blend for memory, there's other tests as well (yes, MemTest, Karhu is good, etc).
 

xray559

Commendable
Jan 2, 2020
65
1
1,535
0
Check CrystalDiskInfo for drive errors/issues. While the SU650/SU655 is not a good drive, it's just as likely your memory had errors at its given speeds/timings (possibly IMC/board limitation) which corrupted data on the disk. You should always test when adding new memory - Prime95 cache can test IMC, blend for memory, there's other tests as well (yes, MemTest, Karhu is good, etc).
My board supports up to 3200(OC) Mhz. Also I ran the windows memory diagnostic, no errors were found. Should I try memtest?
 
Last edited:
Disk info screenshots:
Edit: Ran into a new problem, my windows 10 isn't shutting down nor restarting, or may me just taking a really long time to do either. Already ran another CHKDSK and sfc/scannow. Both didn't seem to fix anything.
View: https://imgur.com/a/GPbFBMB
You might want to swap out the C drive and see if things change.
Perhaps before that reseat the sata data cable and power cable for this disk...test.

What is this virtual disk?
 

ASK THE COMMUNITY