So much more effort than i expected went into this entire process. If i were to start again i think id just roll with stock 😀 Nonetheless im quite proud with my results.
I know there's much room for criticism but it runs nice and i haven't experienced any crashes after disabling C6 and C1E which ran fine with 4.600, but gave me instability with 4.715 (4.8 temps stable but crashing)
I've been reading up here for a while so pushing things to extremes was a conscious decision.
Have some mosfet heatsinks and an extra fan incoming as well.
I found FSB 230 to give me the best performance and the best stability and mostly failures past 250. HT and NB above 2400 always boot failed and at 4.6 and 4.7 at 230fsb 2300 HT & NB gives better stability and performance. Higher Mhz did not always amount to higher performance. K8 enabled and balanced windows energy setting lets me run at nice low frequencies and causes no problems. Other than a 1-3% performance drop in pass mark.
Prime95 blend fails XO somewhere around 5-10 mins for 4.7 and 10-30 mins 4.6
Temps rise with time on prime but given my usual load (some gaming or 100tabs) they never get close to anything worrying.
Under longer strain in prime the cpu starts to throttle but that hasent happened even in cpu intense games. Also Ive had the board shutdown a few times during tests so im feeling all the fail-safes are there.
Anyway here its is... :O and thanks for all the knowledgeable people that let shared the love.
Operating System
Windows 10 Home 64-bit
AMD FX-6300 23 °C
Vishera 32nm Technology
8.00GB Single-Channel DDR3 @ 919MHz (11-11-11-28)
Gigabyte Technology Co., Ltd. GA-78LMT-S2P (Socket M2) Rev. 5
PLE2200 (1680x1050@59Hz)
2047MB NVIDIA GeForce GTX 750 (CardExpert Technology)
931GB Seagate ST1000DM003-1ER162 ATA Device (SATA)
Hyper 212 Evo
PSU 600Silent Take ME
Logic Concept A34 case
http://imgur.com/a/FVsZ8
I know there's much room for criticism but it runs nice and i haven't experienced any crashes after disabling C6 and C1E which ran fine with 4.600, but gave me instability with 4.715 (4.8 temps stable but crashing)
I've been reading up here for a while so pushing things to extremes was a conscious decision.
Have some mosfet heatsinks and an extra fan incoming as well.
I found FSB 230 to give me the best performance and the best stability and mostly failures past 250. HT and NB above 2400 always boot failed and at 4.6 and 4.7 at 230fsb 2300 HT & NB gives better stability and performance. Higher Mhz did not always amount to higher performance. K8 enabled and balanced windows energy setting lets me run at nice low frequencies and causes no problems. Other than a 1-3% performance drop in pass mark.
Prime95 blend fails XO somewhere around 5-10 mins for 4.7 and 10-30 mins 4.6
Temps rise with time on prime but given my usual load (some gaming or 100tabs) they never get close to anything worrying.
Under longer strain in prime the cpu starts to throttle but that hasent happened even in cpu intense games. Also Ive had the board shutdown a few times during tests so im feeling all the fail-safes are there.
Anyway here its is... :O and thanks for all the knowledgeable people that let shared the love.
Operating System
Windows 10 Home 64-bit
AMD FX-6300 23 °C
Vishera 32nm Technology
8.00GB Single-Channel DDR3 @ 919MHz (11-11-11-28)
Gigabyte Technology Co., Ltd. GA-78LMT-S2P (Socket M2) Rev. 5
PLE2200 (1680x1050@59Hz)
2047MB NVIDIA GeForce GTX 750 (CardExpert Technology)
931GB Seagate ST1000DM003-1ER162 ATA Device (SATA)
Hyper 212 Evo
PSU 600Silent Take ME
Logic Concept A34 case
http://imgur.com/a/FVsZ8
Facebook
Twitter
Instagram