Am I going to melt my PC desk? AMD 2800XP 58 degress normal?

G

Guest

Guest
Archived from groups: alt.comp.hardware.overclocking.amd (More info?)

Hey I have been hunting the internet for some advice.
I have overclocked my 2800XP to 2.2ghz and was wondering why it always
says its at about the 60 degree mark.
I understand that this sounds bad but I have a thermaltake silent
boost on it. 4 80mm case fans and an exhaust about an inch away from
my graphics card (X800XL).
The odd thing is my computer seems pretty happy, I dont get crashes
and see no artifacts now that i lowered my cards memory clock.
Any ideas? should i dial it all down again before I make a silicon
toaster?

If i run 3dmark the cpu can get to about 67 i think. Everyone seems to
be saying 40-50 is limit???
 

Chris

Distinguished
Dec 7, 2003
2,048
0
19,780
Archived from groups: alt.comp.hardware.overclocking.amd (More info?)

There is nothing wrong with 58degC. However, 67degC is something to worry
about. Try using Arctic Silver thermal paste and reseat the HS.

--
"All problems have a simple solution! The more complex the solution, the
more ludicrous the analogy!"

"Flinching-Ninja" <utopia_nation@hotmail-dot-com.no-spam.invalid> wrote in
message news:A77Ne.656$j83.484@fe05.news.easynews.com...
> Hey I have been hunting the internet for some advice.
> I have overclocked my 2800XP to 2.2ghz and was wondering why it always
> says its at about the 60 degree mark.
> I understand that this sounds bad but I have a thermaltake silent
> boost on it. 4 80mm case fans and an exhaust about an inch away from
> my graphics card (X800XL).
> The odd thing is my computer seems pretty happy, I dont get crashes
> and see no artifacts now that i lowered my cards memory clock.
> Any ideas? should i dial it all down again before I make a silicon
> toaster?
>
> If i run 3dmark the cpu can get to about 67 i think. Everyone seems to
> be saying 40-50 is limit???
>
 
G

Guest

Guest
Archived from groups: alt.comp.hardware.overclocking.amd (More info?)

Flinching-Ninja wrote:
> Hey I have been hunting the internet for some advice.
> I have overclocked my 2800XP to 2.2ghz and was wondering why it always
> says its at about the 60 degree mark.
> I understand that this sounds bad but I have a thermaltake silent
> boost on it. 4 80mm case fans and an exhaust about an inch away from
> my graphics card (X800XL).
> The odd thing is my computer seems pretty happy, I dont get crashes
> and see no artifacts now that i lowered my cards memory clock.
> Any ideas? should i dial it all down again before I make a silicon
> toaster?
>
> If i run 3dmark the cpu can get to about 67 i think. Everyone seems to
> be saying 40-50 is limit???

Two things:
1) Idle temperatures don't matter a great deal. When idling, both the
chances of an error occuring are small (due to the low temperature) and the
impcact of the error is usually not major.
2) Absolute temperatures don't matter. There is a huge variation (I've seen
30 deg C) between boards and BIOSes, so unless you have made your own
calibrated temperature monitor you really don't have any idea what the CPU
temperature is. Likewise, you cannot compare your temperature to anyone
else's (so there is no "maximum safe temperature" like 50 deg C).

As long as you haven't significantly increased the voltage (over 10%, or
thereabouts), then if the CPU is Prime95 stable (for a reasonable number of
hours, I usually run for 24+ though 10 should be fine) it's not being
damaged by excess heat.

--
Michael Brown
www.emboss.co.nz : OOS/RSI software and more :)
Add michael@ to emboss.co.nz ---+--- My inbox is always open
 
G

Guest

Guest
Archived from groups: alt.comp.hardware.overclocking.amd (More info?)

Cheers for your help guys.
Im gonna cut a vent in the top of my case and add a 120mm fan which
might help.

Any ideas about how to get off a glued on heatsink on a northbridge
chip.

I have a larger zalman heatsink but cant get the old one off. I have
removed the push pins just in case you think im a dunce.
 
G

Guest

Guest
Archived from groups: alt.comp.hardware.overclocking.amd (More info?)

On Sat, 20 Aug 2005 09:32:26 +0000, Flinching-Ninja wrote:

> Any ideas about how to get off a glued on heatsink on a northbridge
> chip.
>
Thin bladed knife works for me.

--
KT133 MB, CPU @2400MHz (24x100): SIS755 MB CPU @2330MHz (10x233)
Need good help? Provide all system info with question.
My server http://wesnewell.no-ip.com/cpu.php
Verizon server http://mysite.verizon.net/res0exft/cpu.htm
 

Dave

Distinguished
Jun 25, 2003
2,727
0
20,780
Archived from groups: alt.comp.hardware.overclocking.amd (More info?)

"Flinching-Ninja" <utopia_nation@hotmail-dot-com.no-spam.invalid> wrote in
message news:A77Ne.656$j83.484@fe05.news.easynews.com...
> Hey I have been hunting the internet for some advice.
> I have overclocked my 2800XP to 2.2ghz and was wondering why it always
> says its at about the 60 degree mark.
> I understand that this sounds bad but I have a thermaltake silent
> boost on it. 4 80mm case fans and an exhaust about an inch away from
> my graphics card (X800XL).
> The odd thing is my computer seems pretty happy, I dont get crashes
> and see no artifacts now that i lowered my cards memory clock.
> Any ideas? should i dial it all down again before I make a silicon
> toaster?
>
> If i run 3dmark the cpu can get to about 67 i think. Everyone seems to
> be saying 40-50 is limit???

Touch the side of the base of the heatsink. If the CPU is actually at 60C
you won't be able to keep your finger on it for longer than a few seconds.

Dave