ASUS P5G41C-M LX 2x4GB 1333 ddr3 RAM

[mrcooperson]

Hello.
Please I need help.
I need put 8Gb RAM in my computer, I have got ASUS P5G41C-M LX with this specifications:

Processors Information
-------------------------------------------------------------------------

Processor 1 ID = 0
Number of cores 2 (max 2)
Number of threads 2 (max 2)
Name Intel Pentium E5400
Codename Wolfdale
Specification Pentium(R) Dual-Core CPU E5400 @ 2.70GHz
Package (platform ID) Socket 775 LGA (0x0)
CPUID 6.7.A
Extended CPUID 6.17
Core Stepping R0
Technology 45 nm
TDP Limit 65 Watts
Core Speed 1199.7 MHz
Multiplier x Bus Speed 6.0 x 200.0 MHz
Rated Bus speed 799.8 MHz
Stock frequency 2700 MHz
Instructions sets MMX, SSE, SSE2, SSE3, SSSE3, EM64T, VT-x
L1 Data cache 2 x 32 KBytes, 8-way set associative, 64-byte line size
L1 Instruction cache 2 x 32 KBytes, 8-way set associative, 64-byte line size
L2 cache 2048 KBytes, 8-way set associative, 64-byte line size
FID/VID Control yes
FID range 6.0x - 13.5x
Max VID 1.288 V

Chipset
-------------------------------------------------------------------------

Northbridge Intel G41 rev. A3
Southbridge Intel 82801GB (ICH7/R) rev. A1
Graphic Interface PCI-Express
PCI-E Link Width x16
PCI-E Max Link Width x16
Memory Type DDR3
Memory Size 4 GBytes
Channels Dual, (Symmetric)
Memory Frequency 399.9 MHz (1:2)
CAS# latency (CL) 6.0
RAS# to CAS# delay (tRCD) 6
RAS# Precharge (tRP) 6
Cycle Time (tRAS) 15
Row Refresh Cycle Time (tRFC) 44
Command Rate (CR) 1T
MCHBAR I/O Base address 0x0FED14000
MCHBAR I/O Size 4096
MCHBAR registers

Memory SPD
-------------------------------------------------------------------------

DIMM # 1
SMBus address 0x50
Memory type DDR3
Module format UDIMM
Manufacturer (ID) Kingston (7F98000000000000)
Size 2048 MBytes
Max bandwidth PC3-10700 (667 MHz)
Part number 99U5471-002.A00LF
Serial number A302C7A3
Manufacturing date Week 39/Year 10
Number of banks 8
Nominal Voltage 1.50 Volts
EPP no
XMP no
AMP no
JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency
JEDEC #1 6.0-6-6-17-23 @ 457 MHz
JEDEC #2 7.0-7-7-20-27 @ 533 MHz
JEDEC #3 8.0-8-8-22-30 @ 609 MHz
JEDEC #4 9.0-9-9-24-33 @ 666 MHz

DIMM # 2
SMBus address 0x52
Memory type DDR3
Module format UDIMM
Manufacturer (ID) Kingston (7F98000000000000)
Size 2048 MBytes
Max bandwidth PC3-10700 (667 MHz)
Part number 99U5471-002.A00LF
Serial number A502BFA3
Manufacturing date Week 39/Year 10
Number of banks 8
Nominal Voltage 1.50 Volts
EPP no
XMP no
AMP no
JEDEC timings table CL-tRCD-tRP-tRAS-tRC @ frequency
JEDEC #1 6.0-6-6-17-23 @ 457 MHz
JEDEC #2 7.0-7-7-20-27 @ 533 MHz
JEDEC #3 8.0-8-8-22-30 @ 609 MHz
JEDEC #4 9.0-9-9-24-33 @ 666 MHz

Display Adapters
-------------------------------------------------------------------------

Display adapter 0
Name NVIDIA GeForce GTX 550 Ti
Board Manufacturer ASUSTeK Computer Inc.
Revision A1
Memory size 1024 MB
PCI device bus 1 (0x1), device 0 (0x0), function 0 (0x0)
Vendor ID 0x10DE (0x1043)
Model ID 0x1244 (0x83C2)
Performance Level Default
Core clock 50.5 MHz
Shader clock 101.0 MHz
Memory clock 135.0 MHz
Performance Level 2D Desktop
Core clock 405.0 MHz
Shader clock 810.0 MHz
Memory clock 324.0 MHz
Performance Level 3D Applications
Core clock 900.0 MHz
Shader clock 1800.0 MHz
Memory clock 2052.0 MHz

Win32_VideoController AdapterRAM = 0x40000000 (1073741824)
Win32_VideoController DriverVersion = 9.18.13.1106
Win32_VideoController DriverDate = 01/18/2013

Software
-------------------------------------------------------------------------

Windows Version Microsoft Windows 7 (6.1) Ultimate Edition 64-bit Service Pack 1 (Build 7601)
DirectX Version 11.0


Please can anyone tell me compatible modules of 4 GB of RAM?
Preferably ddr3 1333 or 1066.
At www.asus.com only appears one of Samsung but I can´t find it.
Thank you so much.

 

[clutchc]

You should be able to use any brand name DDR3 1333/1066/800MHZ memory that runs at 1.5V. The QVL that is listed on the compatible memory page is simply RAM they were able to test before releasing the motherboard for retail. It's not necessary to go by that. Just be sure to buy memory in MATCHED pairs for trouble free operation.

Just remember you can't use DDR2 and DDR3 at the same time. And the E5400 processor only has an 800 MHZ FSB, so it will default to 800MHZ.

 

[mrcooperson]

You should be able to use any brand name DDR3 1333/1066/800MHZ memory that runs at 1.5V. The QVL that is listed on the compatible memory page is simply RAM they were able to test before releasing the motherboard for retail. It's not necessary to go by that. Just be sure to buy memory in MATCHED pairs for trouble free operation.

Just remember you can't use DDR2 and DDR3 at the same time. And the E5400 processor only has an 800 MHZ FSB, so it will default to 800MHZ.

Thank you very much.
I'll try this one:
http://www.kingston.com/us/hyperx/memory/fury?ktc_campaign=HXEMEA&gclid=CNOpq7aShr8CFUn4wgodgIAAOg

 

[clutchc]

Should be fine. Which speed are you going to get; 1333MHz, 1600MHz, or 1866MHz?

 

[mrcooperson]

You should be able to use any brand name DDR3 1333/1066/800MHZ memory that runs at 1.5V. The QVL that is listed on the compatible memory page is simply RAM they were able to test before releasing the motherboard for retail. It's not necessary to go by that. Just be sure to buy memory in MATCHED pairs for trouble free operation.

Just remember you can't use DDR2 and DDR3 at the same time. And the E5400 processor only has an 800 MHZ FSB, so it will default to 800MHZ.

Should be fine. Which speed are you going to get; 1333MHz, 1600MHz, or 1866MHz?

I am going to get 1333MHz. But can I take the others too?

 

[clutchc]

The faster speeds will probably work OK, just default to the slower speeds. Since the timings may vary considerably unless you set them yourself, I would stick with the 1333MHZ.

 

[mrcooperson]

The faster speeds will probably work OK, just default to the slower speeds. Since the timings may vary considerably unless you set them yourself, I would stick with the 1333MHZ.

I can not use hyperx 1333MHz fury, they do not work.
I read that it may be because they are dual and my motherboard does not support them.

 

[clutchc]

Dual? What do you mean? If you mean double sided, your board does support double sided memory. The only disclaimer I found is that it doesn't support DIMMS of 256 Mb or less.

You did take out any DDR2 memory sticks right? You can't populate all 4 slots at the same time.

 

[mrcooperson]

Dual? What do you mean? If you mean double sided, your board does support double sided memory. The only disclaimer I found is that it doesn't support DIMMS of 256 Mb or less.

You did take out any DDR2 memory sticks right? You can't populate all 4 slots at the same time.

I'm only using 2 slots of DDR3 RAM memory but not working.
I tested with KVR13N9S8 / 4 Kingston and not working.
I sent an email to Kingston and they tell me they have no current RAM memory supported.
I do not know what else to do, I have seen this website:
http://www.offtek.co.uk/ram-memory-2/asus/asus-motherboard-memory/p5g41c-m-lx/mid172964 #
Maybe I try them. What do you think?

 

[clutchc]

I think you have some other issue. I've never had a board that didn't accept any brand memory that met the specs. Try just one stick in whichever DIMM slot that your MB manual suggests when using one stick.

Which version is your MB BIOS? I see the latest version offered for that board dealt with memory compatibility: http://www.asus.com/Motherboards/P5G41CM_LX/HelpDesk_Download/
Be sure you have the latest version.

 

[mrcooperson]

I think you have some other issue. I've never had a board that didn't accept any brand memory that met the specs. Try just one stick in whichever DIMM slot that your MB manual suggests when using one stick.

Which version is your MB BIOS? I see the latest version offered for that board dealt with memory compatibility: http://www.asus.com/Motherboards/P5G41CM_LX/HelpDesk_Download/
Be sure you have the latest version.

I've tried to put only one memory, and even combine it with mine, and nothing.
My 2x2GB RAM do work perfectly.
The firmware is the latest BIOS for Windows 7 64bit, the 0702
Any more idea?

 

[mrcooperson]

anyone can help me, please?

 

[mrcooperson]

I think you have some other issue. I've never had a board that didn't accept any brand memory that met the specs. Try just one stick in whichever DIMM slot that your MB manual suggests when using one stick.

Which version is your MB BIOS? I see the latest version offered for that board dealt with memory compatibility: http://www.asus.com/Motherboards/P5G41CM_LX/HelpDesk_Download/
Be sure you have the latest version.

Please, any more ideas?

 

[Hannibalz]

I have the same problem too. I'm using a hyper x fury 8gb ddr3 single dimm and it has 1333mhz to 1866mhz. Apparently when installed it the computer powerful but not booting. Have you solved this problem?