Asus Z87-A Intel Haswell 4770-k Corsair 100i PC Restarting during rendering.

[Soumin]

Ideally it is OK.My PC is restarting during rendering in 3DS Max Vray after 10 to 15 min.In Idle mode My cpu temp is 40-43c & Mother board temp is 43 c. when i am starting rendering temp boosts to 85 to 88 c and it is restarting after some time like win 8 blue screen collecting error .My Rigs is
Cabinet-Corsair 200R
Processor-Intel Haswell4770k
MB-Asus Z 87-A
RAM-Kingstone Hyper x 8 gb 1600
3 HDDs
Corsair H100i CPU Cooler
power supply-Zebronic 750W

In my boards there are 5 fans ports available(1 cpu fan port,1cpu_opt,3 chasis fan ports)I have connected my fans of H100i in cpu_opt fan pin and chasis fan 1 port & the cpu fan in cpu fan pin.
remaining 2 fans are connected in chasis fan port .
Why my Pc restarting ????

Cooling unit ,Power supply or Memory problem...any suggestion?

 

[thunderdan602]

Connect your h100i fans to the cpu fan port. Your h100i should have come with an adapter that allows you to plug both fans into that cpu fan port. Do now worry about the power, as you should have plugged the H100i on to the power supply, so the cooler should be getting plenty of power.

 

[Soumin]

Connect your h100i fans to the cpu fan port. Your h100i should have come with an adapter that allows you to plug both fans into that cpu fan port. Do now worry about the power, as you should have plugged the H100i on to the power supply, so the cooler should be getting plenty of power.

Thanks 4 ur reply @thunderdan602 !I changed the connection. Now my 2 fans are connected with the 2-1 wire came with cooler and it connected in the top of the cpu fan port.Result is ..Now both fans are runningin dependently where b4 Asus fanexpert software utility control my corsair fan and one fan always stoped which connected in cpu_opt port in standard mode rather than iit was also working in fan full speed mode. !;-)

But problem is not solved..Temp same about to burn my haswell it same 88 89 c when i render..
Do I need to change the PSU 1000 Watt.,,Or wastage of money ..any idea

 

[Supernova1138]

Try remounting your cooler, be sure to clean off the old thermal paste and reapply it. A small peas sized drop on the middle of the CPU heat spreader should be sufficient. If your temps are still high after remounting the cooler, then you probably have a defective water cooler that isn't pumping the water to the radiator, causing the high temps.

Zebronics is a pretty bad brand for power supplies, and that may be an issue too, but I would try resolving issues with your CPU cooler and see if that improves stability first.

 

[thunderdan602]

Soumin, try Supernovas idea. I know Haswells run warm, but the h100i should be cooling better than what it is now. I would also make sure that you have enough cool air coming into your case and that your venting the hot air correctly. I have read where people are using the h100i fans to push air from the top of the case through the rad, and on paper that seems like a good idea. But people forget hot air rises, so in essence In those situations the hot air is being generated by the gpu and other internal components and not venting but getting trapped in the case. ideally you should have cool air being brought in from the front of the case and bottom of the case (if your case has that feature) and the warm air should be pushed or vented out the top rear and top of the case. Make sense?

 

[Soumin]

Soumin, try Supernovas idea. I know Haswells run warm, but the h100i should be cooling better than what it is now. I would also make sure that you have enough cool air coming into your case and that your venting the hot air correctly. I have read where people are using the h100i fans to push air from the top of the case through the rad, and on paper that seems like a good idea. But people forget hot air rises, so in essence In those situations the hot air is being generated by the gpu and other internal components and not venting but getting trapped in the case. ideally you should have cool air being brought in from the front of the case and bottom of the case (if your case has that feature) and the warm air should be pushed or vented out the top rear and top of the case. Make sense?

Thanks 4 replys.Only one thing let me know,is the consumption of power gradually increased ?

 

[Soumin]

Problem solved. 🙂There are no issue in Hard ware .issue was in software setting ASUS Performance and power saving utility.Now I've created two Over clocking Profiles in TurboV Evo.one is for quckrender one is for long time render .