ASUS Z97-I Plus, not getting boot/black screen and no lights in KeyB or mouse

[Trophyon]

Newly built pc. No signal on screen, no lights in keyboard or mouse (connected to usb 2) green light beside ram, and red light beside CPU (Manual says it's DRAM led) The PC just turns on and off right after, stuck on loop. Some of the parts like the SSD has been in use before, and was not formatted. But I doubt that's the reason since it will be later on,

I have no idea what to do., so help would be greatly appreciated!

Mobo: ASUS Z97I-plus
RAM: Crucial Ballistix 1600 mhz, 2x8gb ddr3
CPU: Intel i5 4690k (no OC)
GPU: EVGA GTX 770 SC 4gb
Corsair TX750M PSU

Checked the GPU, PSU and RAM, nothing wrong with those when installed in other systems.

Sorry for bad picture.

 

[alexoiu]

Check if memory properly inserted (some require more force). Try leaving single RAM module installed and testing each slot.

 

[Trophyon]

Check if memory properly inserted (some require more force). Try leaving single RAM module installed and testing each slot.

Forgot to mention that,. I did do all the above. Still nothing.

 

[alexoiu]

What are the last 4 digits on a sticker like http://www.guru3d.com/miraserver/images/2011/990fx-sabertooth/IMG_4499.jpg ?

 

[Trophyon]

What are the last 4 digits on a sticker like http://www.guru3d.com/miraserver/images/2011/990fx-sabertooth/IMG_4499.jpg ?

I can't see a sticker like that anywhere, guess i'll have to take everything apart then..

 

[alexoiu]

Bottom side, near the PCIe slot.

 

[Trophyon]

Bottom side, near the PCIe slot.

Sorry for taking so long, I was caught up in alot of stuff, I hope you're still with me here! I found the number for you!

 

[alexoiu]

No problem.
CPU is supported. Try removing the CPU and see if any bent pins.

 

[Trophyon]

No problem.
CPU is supported. Try removing the CPU and see if any bent pins.

I removed the CPU and no pins were bent. But I noticed something strange, I had used the intel stock cooler for a bit and it looked like it hadn't had proper contact with the CPU. I changed it to the H80i and assembled it all back. Still the same result as before. I was hoping so badly it was just the bad contact of the cooler that caused the problem. Now I have no idea.

 

[alexoiu]

Can you post a picture of the motherboard?

 

[Trophyon]

Can you post a picture of the motherboard?

How do you want it, with CPU out and everything?

 

[alexoiu]

Try taking the board out of the case, removing the CPU,and posting a picture of the CPU socket.

 

[Trophyon]

Try taking the board out of the case, removing the CPU,and posting a picture of the CPU socket.

I really hope I haven't taken to long for this but here goes! This is the best pictures I managed to take. Hope they suffice!

(hope pictures works this time! )

 

[alexoiu]

Pins look ok. If you haven't solved the problem so far, I suggest RMA-ing both board and CPU.

 

[Trophyon]

Pins look ok. If you haven't solved the problem so far, I suggest RMA-ing both board and CPU.

I didn't mention this for some reason when posting this. BUT the mobo and th CPU had been in use for over a year. It was working perfectly before, but after reassembly it just stopped working. I was careful with static electricity, so it bugs me alot not figuring out what caused this.

 

[Trophyon]

So I recorded a short video clip of the mobo while the PC is running, I doubt it's gonna be more of help for any of you out there! But here it is anyways:
https://www.dropbox.com/s/3tej7bmikubjmow/MOV_0007.mp4?dl=0