Biostar H55A+ will not detect WD 500gb Caviar Blue

JTTS

Distinguished
Jul 13, 2011
8
0
18,510
Hey everyone, just joined but i have used this place to help me unlock the mysteries that are associated with building your own system

My current problem is as follows:

I recently purchased an Intel i3 3.08ghz processor, 4gb of G.SKILL 1333 mhz ddr3 RAM, a BIOSTAR H55A+ Mobo, and a Western Digital 500gb Caviar Blue HDD along with a copy of Win7 (32bit home) which i have installed on the HDD.
(if its any help im also SLI'ing an XFX and an EVGA 8800GT)

However, with my new motherboard installed, i cannot seem to get it to detect the WD HDD (which is connected via SATA).

I have tried both the IDE and the AHCI settings in BIOS and neither seem to be the solution

I should also add that I have not yet been able to install the software on the CD that came with my biostar, because my CD drive is an IDE drive, and the H55A+ does not have any IDE slots.

Any advice would be greatly appreciated, because im starting to get really frustrated with all this.
 

JTTS

Distinguished
Jul 13, 2011
8
0
18,510
[frustration]well ill have to get a new CD/DVD drive to reinstall, because this new MOBO doesnt have any IDE ports, which is coincidentally what my cd drive needs [/frustration]
 

JTTS

Distinguished
Jul 13, 2011
8
0
18,510
Well i got a new SATA DVD drive, and now win7 says it cannot install to my HDD, ive tried using diskpart to clean my HDD, and it came up with an I/O error. now diskpart does not even see any disks. this is supremely frustrating,
 

rvilkman

Distinguished
That does seem to limit the problem to a few of locations:

- Sata data cable
- Sata power cable
- Motherboard sata controller ( if the DVD drive works this is less likely)
- Motherboard sata connector
- the hard drive is simply broken.
 

JTTS

Distinguished
Jul 13, 2011
8
0
18,510
Is there some driver from my motherboards CD that i could point to during installation to get this to work? Or could i take this HDD and attempt to stick it in my Blacx Thermaltake Internal to External thing and try and manually create some partitions using a program or something?

If not, im probably just going to try and RMA this WD HDD to newegg and see if i cant finally get this problem solved


If it is any help, when i first got Win7 to install on this HDD on my old motherboard (just a day or 2 before i ended up replacing that board with this new biostar and all these problems began) it did install correctly, and i got to the desktop and everything. I then went to my computer and just for kicks tried to do the windows power index rating thing or whatever it is (the numerical measurement of your computers ability) and it ran for a little then appeared to freeze, i tried ctrl alt deleting out of it, froze the whole system and had to do a "hard" power off. Perhaps the HDD did actually start failing then, idk.

thanks again for the help
 

grody

Distinguished
Nov 10, 2009
202
0
18,710
Do what rvilkman suggested:
- try a different sata cable
- try a different sata power connector
- try a different sata port on the mobo

There's about a 10% this will fix it, but that will probably be because of a loose connection rather than a bad one.

If that doesn't do it, it is new HDD time.
 

JTTS

Distinguished
Jul 13, 2011
8
0
18,510
thanks for the help guys, ive already tried different cables and power connectors as well as different ports. i put the HDD into my Thermaltake BlacX external dock and stuck it into a rig running XP and snooped around in the device manager. When i found the correct disk drive and went to volume and hit populate it said the disk was unreadable and had an unknown type/partition.

Im RMAing it via newegg as i type this. hopefully the next one will be in better shape
 

ps3hacker12

Distinguished


this is what i used, works fine to this day (its an IDE to sata converter):
http://www.ebay.co.uk/itm/Serial-SATA-Motherboard-IDE-HD-Converter-Adapter-A23-/300572529416?pt=UK_Computing_CablesConnectors_RL&hash=item45fb84d308

[EDIT]:
just read the rest of the thread, is that HDD pulled from an older OEM system? (such as a HP/dell system?) if so it may be OEM locked.
 

JTTS

Distinguished
Jul 13, 2011
8
0
18,510
no the HDD is brand new from Newegg, and my BIOS is already set for sata to act like IDE anyways so idk if thatll help, not to mention my mobo has no IDE port
 

JTTS

Distinguished
Jul 13, 2011
8
0
18,510
well i think i solved my problem, apparently i was unaware that windows 7 OEM is locked to motherboards when you install it, and since i had installed it before my new motherboard arrived i had doomed myself from the beginning. maybe its just me but does the fact that MS does that not seem kind of ridiculous to anyone else?
 

rvilkman

Distinguished
I don't think it would still cause the mentioned issues, you may have to call Microsoft to reactivate your windows, but it should still boot up just fine regardless.

The feature you are mentioning is actually for all the versions both OEM and regular, once windows notices you have changed 'too many' components it requires a re-activation. Which you can do simply by calling them.