Can't find the router's IP address

[limewired]

I have an Edimax BR-6228nS and I set it up as an access point a while ago. I also changed a lot of settings on there and even turned off the DHCP. I need to use it as a router now so I am trying to get into the configure page. After resetting the router, the IP address is still the not the default one. I still can't access it. When I type in ipconfig in the command prompt all it shows is the ip address that connects to my modem. This is what it shows when i type in ipconfig /all. 192.168.15.3 only directs me to my modem's set up page. This is confusing me, is the router not being recognized?

Windows IP Configuration

Host Name . . . . . . . . . . . . : --------
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Mixed
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller
Physical Address. . . . . . . . . : 00-30-67-C3-F8-F4
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::5158:ff54:8adb:9341%11(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.15.3(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Thursday, February 23, 2012 4:29:02 PM
Lease Expires . . . . . . . . . . : Thursday, February 23, 2012 5:29:01 PM
Default Gateway . . . . . . . . . : 192.168.15.1
DHCP Server . . . . . . . . . . . : 192.168.15.1
DHCPv6 IAID . . . . . . . . . . . : 234893415
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-15-A8-99-AB-00-30-67-C3-F8-F4

DNS Servers . . . . . . . . . . . : 192.168.15.1
NetBIOS over Tcpip. . . . . . . . : Enabled

Tunnel adapter isatap.{5C44B350-A440-44C3-BC77-E15C7C85C752}:

Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes

Tunnel adapter Teredo Tunneling Pseudo-Interface:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:10af:a01:3f57:f0fc(Prefe
rred)
Link-local IPv6 Address . . . . . : fe80::10af:a01:3f57:f0fc%12(Preferred)
Default Gateway . . . . . . . . . : ::
NetBIOS over Tcpip. . . . . . . . : Disabled

 

[Emerald]

192.168.15.1

 

[limewired]

When I said 192.168.15.3 I meant 192.168.15.1. Sorry for the confusion, the router acts like it's not there but clearly the modem is connected to the router and connected to my computer.

 

[ngrego]

Your modem is handeling the DHCP on your network so you can find the address of the router from the DHCP pool on your modem. Enter your modem setup, go to DHCP settings and you will find a list of connected devices. Each of the connected devices has an address and a hostname. Look through the list and you should find your router there. Type the address of the router (you found in the DHCP list) into your browser. You should now see the login page of your router.
You should asign a static IP to your router, something like 192.168.15.2 so you can find it every time. You can also start your DHCP address pool at 192.168.15.10-192.168.15.50 use the first 10 addresses for your networking hardware etc.

 

[Emerald]

the default IP for this router is 192.168.2.1

assign a static IP of 192.168.2.5 to your computer and enter the router IP in your browser.

do not forget the set the computer back to the old settings after you are done