Hard Disk Drive poor performance and S.M.A.R.T errors on some attributes but the smart status shows ok

[Sohom]

Hi,
I have had some issues while playing star wars battlefront where my seagate disk usage would jump to 100%. Sometimes while copying files from this drive the explorer would crash. So, i checked the SMART attributes using HDTunes pro, and i was confused about some attributes which didn't seem right...
I am attaching the link to the the pics, where u can see The spin up time of seagate hdd is 0 ms, raw read error rate is high, there are seek error rates and the Head flying hours of my seagate drive is insanely high. There are other attributes too, even the smart values of my SSD doesnt seem so good... I am a little confused about the values coz i don't have better understanding of the attributes. So can u guys pls help me regarding this and confirm whether my disk SMART values are ok or not.... I have a lot of important data on the drives and don't want to lose it... I do format my drives a lot.... My seagate hard disk is just a few months old...

Update:
HDTune Pro results:
https://ibb.co/gQ2eDv - Seagate HDD
https://ibb.co/hqun0a - Transcend SSD

Edit: i did post speccy smart values first but that seemed to be way off the mark...

Guys i really need help with this problem, i am more worried about the seagate drive as i store all my data on this drive. I did contact Seagate customer care and they asked me to run seatools for dos and when i did the drive wasn't detected... So i'm in contact with seagate customer support but i want some expert opinion here coz i lost all my data on my previous seagate drive. Though i did take a backup this time but still want to know whether the drive is ok or not...

 

[RolandJS]

Try HD Sentinal free version for a solid 2nd opinion; according to some sources, HD information reported may or may not be representative of daily averages.

 

[Sohom]

ok. So yeah i checked with HDTune Pro... and the result are somewhat different.... Here it shows high seek error rate and raw read error rate on the seagate drive... and on the transcend ssd page it shows attention on interface crc error count

https://ibb.co/gQ2eDv - Seagate HDD
https://ibb.co/hqun0a - Transcend SSD

 

[Sohom]

Try HD Sentinal free version for a solid 2nd opinion; according to some sources, HD information reported may or may not be representative of daily averages.

So I checked out the smart values with HDDSentinel and here are the results

For the seagate drive:

1,Raw Read Error Rate,6,117,99,OK,000007CCB5C8,0,Enabled
3,Spin Up Time,0,96,96,OK (Always passing),000000000000,0,Enabled
4,Start/Stop Count,20,100,100,OK,00000000012B,0,Enabled
5,Reallocated Sectors Count,10,100,100,OK,000000000000,0,Enabled
7,Seek Error Rate,30,70,60,OK,000000B8F2C5,0,Enabled
9,Power On Time Count,0,99,99,OK (Always passing),000000000671,0,Enabled
10,Spin Retry Count,97,100,100,OK,000000000000,0,Enabled
12,Drive Power Cycle Count,20,100,100,OK,0000000000F1,0,Enabled
183,SATA Downshift Count,0,100,100,OK (Always passing),000000000000,0,Enabled
184,End-to-End Error Count,99,100,100,OK,000000000000,0,Enabled
187,Reported Uncorrectable Errors,0,100,100,OK (Always passing),000000000000,0,Enabled
188,Command Timeout,0,100,100,OK (Always passing),000000000000,0,Enabled
189,High Fly Writes,0,100,100,OK (Always passing),000000000000,0,Enabled
190,Airflow Temperature,45,61,59,OK,0000281C0027,0,Enabled
191,G-Sense Error Rate,0,100,100,OK (Always passing),000000000000,0,Enabled
192,Power off Retract Cycle Count,0,100,100,OK (Always passing),00000000001A,0,Enabled
193,Load/Unload Cycle Count,0,100,100,OK (Always passing),0000000002FA,0,Enabled
194,Disk Temperature,0,39,41,OK (Always passing),001300000027,0,Enabled
197,Current Pending Sector Count,0,100,100,OK (Always passing),000000000000,0,Enabled
198,Off-Line Uncorrectable Sector Count,0,100,100,OK (Always passing),000000000000,0,Enabled
199,Ultra ATA CRC Error Count,0,200,200,OK (Always passing),000000000000,0,Enabled
240,Head Flying Hours,0,100,253,OK (Always passing),D4CB0000064A,0,Enabled
241,Total LBA Written,0,100,253,OK (Always passing),0004615C8121,0,Enabled
242,Total LBA Read,0,100,253,OK (Always passing),00088E1DD7E0,0,Enabled

for the WDBlue drive:

1,Raw Read Error Rate,51,200,200,OK,000000000000,0,Enabled
3,Spin Up Time,21,174,173,OK,0000000008E3,0,Enabled
4,Start/Stop Count,0,100,100,OK (Always passing),000000000014,0,Enabled
5,Reallocated Sectors Count,140,200,200,OK,000000000000,0,Enabled
7,Seek Error Rate,51,100,253,OK,000000000000,0,Enabled
9,Power On Time Count,0,100,100,OK (Always passing),000000000036,0,Enabled
10,Spin Retry Count,51,100,253,OK,000000000000,0,Enabled
11,Drive Calibration Retry Count,0,100,253,OK (Always passing),000000000000,0,Enabled
12,Drive Power Cycle Count,0,100,100,OK (Always passing),000000000014,0,Enabled
183,SATA Downshift Count,0,100,100,OK (Always passing),000000000000,0,Enabled
184,End-to-End Error Count,97,100,100,OK,000000000000,0,Enabled
187,Reported Uncorrectable Errors,0,100,100,OK (Always passing),000000000000,0,Enabled
188,Command Timeout,0,100,100,OK (Always passing),000000000000,0,Enabled
190,Airflow Temperature,40,60,59,OK,0000281E0028,0,Enabled
192,Power off Retract Cycle Count,0,200,200,OK (Always passing),000000000000,0,Enabled
193,Load/Unload Cycle Count,0,200,200,OK (Always passing),000000000016,0,Enabled
194,Disk Temperature,0,103,102,OK (Always passing),000000000028,0,Enabled
196,Reallocation Event Count,0,200,200,OK (Always passing),000000000000,0,Enabled
197,Current Pending Sector Count,0,200,200,OK (Always passing),000000000000,0,Enabled
198,Off-Line Uncorrectable Sector Count,0,100,253,OK (Always passing),000000000000,0,Enabled
199,Ultra ATA CRC Error Count,0,200,200,OK (Always passing),000000000000,0,Enabled
200,Write Error Rate,0,100,253,OK (Always passing),000000000000,0,Enabled

And for the transcend ssd:

1,Read Error Rate,0,100,100,OK (Always passing),000000000000,0,Enabled
5,Reallocated Sectors Count,0,100,100,OK (Always passing),000000000000,0,Enabled
9,Power On Time Count,0,100,100,OK (Always passing),0000000010EF,0,Enabled
12,Power Cycle Count,0,100,100,OK (Always passing),000000000E0F,0,Enabled
192,Power-off Retract Count,0,100,100,OK (Always passing),0000000003E7,0,Enabled
194,Controlled Temperature,0,100,100,OK (Always passing),00000000002D,0,Enabled
195,Hardware ECC Recovered,0,100,100,OK (Always passing),000000017883,0,Enabled
196,Reallocation Event Count,16,100,100,OK,000000000000,0,Enabled
197,Current Pending Sector Count,0,100,100,OK (Always passing),000000000000,0,Enabled
199,UltraDMA CRC Error Count,50,100,100,OK,000000000014,0,Enabled
160,Uncorrectable Sectors Count (Read/Write),0,100,100,OK (Always passing),000000000000,0,Enabled
161,Number of Valid Spare Blocks,0,100,100,OK (Always passing),000000000025,0,Enabled
163,Number of Initial Invalid Blocks,0,100,100,OK (Always passing),000000000021,0,Enabled
164,Total Erase Count,0,100,100,OK (Always passing),000000003BA7,0,Enabled
165,Maximum Erase Count,0,100,100,OK (Always passing),000000000032,0,Enabled
166,Minimum Erase Count,0,100,100,OK (Always passing),000000000005,0,Enabled
167,Average Erase Count,0,100,100,OK (Always passing),00000000000F,0,Enabled
168,Max Erase Count of Spec,0,100,100,OK (Always passing),000000000BB8,0,Enabled
169,Remain Life Percentage,0,100,100,OK (Always passing),000000000064,0,Enabled
232,Available Reserved Space,0,100,100,OK (Always passing),000000000064,0,Enabled
177,Total Wearlevel Count,50,100,100,OK,00000000002F,0,Enabled
181,Total Program Fail Count,0,100,100,OK (Always passing),000000000000,0,Enabled
182,Total Erase Fail Count,0,100,100,OK (Always passing),000000000000,0,Enabled
241,Total Data Written (32MB),0,100,100,OK (Always passing),000000045A9F,0,Enabled
242,Total Data Read (32MB),0,100,100,OK (Always passing),000000059976,0,Enabled

 

[RolandJS]

Wow, different report breakouts from different utilities!