i was using the acronis program to clone as it was the recommended program from crucialI don't know what tool you're using, but it should be OK.
I use Macrium Reflect.
Specific steps for a successful clone operation:
Verify the actual used space on the current drive is significantly below the size of the new SSD
Both drives must be the same partitioning scheme, either MBR or GPT
Download and install Macrium Reflect (or Samsung Data Migration, if a Samsung target SSD)
If you are cloning from a SATA drive to PCIe/NVMe, you may need to install the relevant driver for this new NVMe/PCIe drive.
Disconnect ALL drives except the current C and the new SSD
Run the Macrium Reflect (or Samsung Data Migration)
Select ALL the partitions on the existing C drive
[Ignore this section if using the SDM. It does this automatically]
If you are going from a smaller drive to a larger, by default, the target partition size will be the same as the Source. You probably don't want that
You can manipulate the size of the partitions on the target (larger)drive
Click on "Cloned Partition Properties", and you can specify the resulting partition size, to even include the whole thing
Click the 'Clone' button
Wait until it is done
When it finishes, power off
Disconnect ALL drives except for the new SSD. This is not optional.
This is to allow the system to try to boot from ONLY the SSD
(swapping cables is irrelevant with NVMe drives, but DO disconnect the old drive for this next part)
Swap the SATA cables around so that the new drive is connected to the same SATA port as the old drive
Power up, and verify the BIOS boot order
If good, continue the power up
It should boot from the new drive, just like the old drive.
Maybe reboot a time or two, just to make sure.
If it works, and it should, all is good.
Later, reconnect the old drive and wipe all partitions on it.
This will probably require the commandline diskpart function, and the clean command.
Ask questions if anything is unclear.
With most current tools, like Macrium Reflect, physical drive size does not matter.That looks like you are trying to clone a 2TB disk to a 1TB disk.
Unless you do some shrinkage that's not going to work.
Macrium may clone only the data that does not mean Acronis does.With most current tools, like Macrium Reflect, physical drive size does not matter.
They are only concerned with the size of the data.
Here, there only appears to be about 500GB consumed on the current C drive.
Absent any other problems, Macrium will do this going into a 1TB drive no problem.
Acronis, I believe, does the same thing.Macrium may clone only the data that does not mean Acronis does.
I used some cloning tool in the past and it did a sector by sector clone.
Like watching paint dry.
|Thread starter||Similar threads||Forum||Replies||Date|
|T||Question Cloning a boot drive to new larger drive.||Storage||7|
|Question I have a m.2 drive that is my third SSD and I want to wipe all the data on it so I can clone my c drive to it.||Storage||8|
|W||Question Using ddrescue or other cloning software for an HDD with bad sectors ?||Storage||0|
|L||Question SSD SATA drive disappears after cloning to it||Storage||17|
|W||Question SSD Cloning Using Startech Duplicator||Storage||39|
|B||Question What's The Best Way to Clone and Replace an M.2?||Storage||5|
|Question Cloning of SanDisk NVMe M.2 SSD to a like drive using a SABRENT EC-SSD2 with offline cloning||Storage||7|
|L||Question Problems Cloning with Macrium ?||Storage||5|
|A||Question Cloned NVMe won't boot Win10||Storage||10|
|S||[SOLVED] Setting NVMe SSD to default boot device after clone ?||Storage||8|
|Question Cloning a boot drive to new larger drive.|
|Question I have a m.2 drive that is my third SSD and I want to wipe all the data on it so I can clone my c drive to it.|
|Question Using ddrescue or other cloning software for an HDD with bad sectors ?|
|Question SSD SATA drive disappears after cloning to it|
|Question SSD Cloning Using Startech Duplicator|
|Question What's The Best Way to Clone and Replace an M.2?|
|Question Cloning of SanDisk NVMe M.2 SSD to a like drive using a SABRENT EC-SSD2 with offline cloning|
|Question Problems Cloning with Macrium ?|
|Question Cloned NVMe won't boot Win10|
|[SOLVED] Setting NVMe SSD to default boot device after clone ?|