I recently encountered an error that looks like S.M.A.R.T detection failed or something, I used HDDScan and here're the result:
HDDScan S.M.A.R.T. Report HDD
State:
Model: Hitachi HTS541680J9SA00
Firmware: SB2OC70P
Serial: SB2241SGE9BXJE
LBA: 156301488 (80 GB)
Report By: HDDSCAN v4.1
Report Date: 8/1/2020 1:39:47 PM
Num Attribute Name Value Worst Raw(hex) Threshold
001 Raw Read Error Rate 095 095 0000000000-000F 062
002 Throughput performance 100 100 0000000000-0000 040
003 Spin Up Time 253 253 0000090000-0000 033
004 Start/Stop Count 096 096 0000000000-1C9F 000
005 Reallocation Sector Count 004 004 0000000000-0000 005
007 Seek Error Rate 100 100 0000000000-0000 067
008 Seek time Performance 100 100 0000000000-0000 040
009 Power-On Hours Count 074 074 0000000000-2D9F 000
010 Spin Retry Count 100 100 0000000000-0000 060
012 Device Power Cycle Count 096 096 0000000000-1C83 000
191 G-sense Rate/Servo tracking 100 100 0000000000-0000 000
192 Emergency Retract Count 099 099 0000000000-015F 000
193 Load/unload Cycle Count 041 041 0000000009-22E9 000
194 HDA Temperature 112 112 49 C 000
194 HDA Temperature Maximum 112 112 54 C 000
194 HDA Temperature Minimum 112 112 23 C 000
196 Reallocation Event Count 004 004 0000000000-12AD 000
197 Current Pending Errors Count 100 100 0000000000-0062 000
198 Uncorrectable Errors Count 100 100 0000000000-0000 000
199 UltraDMA CRC Errors 200 253 0000000000-0000 000
223 Load Retry Count 100 100 0000000000-0000 000
The Reallocation Sector Count got an 'x' over it, seems like a bad sign, and I don't know what's going on
Please give me some answer, helps are appreciated , thank you
=)
HDDScan S.M.A.R.T. Report HDD
State:
Model: Hitachi HTS541680J9SA00
Firmware: SB2OC70P
Serial: SB2241SGE9BXJE
LBA: 156301488 (80 GB)
Report By: HDDSCAN v4.1
Report Date: 8/1/2020 1:39:47 PM
Num Attribute Name Value Worst Raw(hex) Threshold
001 Raw Read Error Rate 095 095 0000000000-000F 062
002 Throughput performance 100 100 0000000000-0000 040
003 Spin Up Time 253 253 0000090000-0000 033
004 Start/Stop Count 096 096 0000000000-1C9F 000
005 Reallocation Sector Count 004 004 0000000000-0000 005
007 Seek Error Rate 100 100 0000000000-0000 067
008 Seek time Performance 100 100 0000000000-0000 040
009 Power-On Hours Count 074 074 0000000000-2D9F 000
010 Spin Retry Count 100 100 0000000000-0000 060
012 Device Power Cycle Count 096 096 0000000000-1C83 000
191 G-sense Rate/Servo tracking 100 100 0000000000-0000 000
192 Emergency Retract Count 099 099 0000000000-015F 000
193 Load/unload Cycle Count 041 041 0000000009-22E9 000
194 HDA Temperature 112 112 49 C 000
194 HDA Temperature Maximum 112 112 54 C 000
194 HDA Temperature Minimum 112 112 23 C 000
196 Reallocation Event Count 004 004 0000000000-12AD 000
197 Current Pending Errors Count 100 100 0000000000-0062 000
198 Uncorrectable Errors Count 100 100 0000000000-0000 000
199 UltraDMA CRC Errors 200 253 0000000000-0000 000
223 Load Retry Count 100 100 0000000000-0000 000
The Reallocation Sector Count got an 'x' over it, seems like a bad sign, and I don't know what's going on
Please give me some answer, helps are appreciated , thank you
=)