HP LaserJet III and PostScript

Toggle sidebar Toggle sidebar
M

Michael

Distinguished
Dec 31, 2007
1,318
0
19,280
Archived from groups: comp.periphs.printers (More info?)

How does one tell if a particular LJ-III has the "optional" PostScript
feature? I have no docs. for the LJ-III that I picked up recently, and
I see no menu item that appears to address PostScript. This printer
does have an HP PostScript Cartridge Plus (C2089A) plugged in but that's
just fonts, isn't it?

I used to have an IBM 4029 w/ PostScript that I used with an old DOS
graphics package for laying out and printing PC board artwork. That
package's available driver selection offers only a Postscript drivers
for LJ-III, so I selected that driver and printed an old piece of
artwork to my LJ-III. The output looked like I had sent a PostScript
data stream to a non-Postcript printer .... lots of text. Do I have to
select PostScript mode on the printer? How do I do that?

Michael
 
Archived from groups: comp.periphs.printers (More info?)

Michael <NoSpam@att.net> wrote:
> How does one tell if a particular LJ-III has the "optional" PostScript
> feature? I have no docs. for the LJ-III that I picked up recently, and
> I see no menu item that appears to address PostScript. This printer
> does have an HP PostScript Cartridge Plus (C2089A) plugged in but that's
> just fonts, isn't it?

Looks like it's a full PostScript level 2 implementation. Genuine
Adobe, even.

The printer has a 68000 processor running at 10 or 16 MHz, so it's not
likely to interpret PostScript very quickly. Try it on a reference
document and time it. Then remove the C2089A and run the same document
through Ghostscript on your computer, feeding PCL output to the printer.

> I used to have an IBM 4029 w/ PostScript that I used with an old DOS
> graphics package for laying out and printing PC board artwork. That
> package's available driver selection offers only a Postscript drivers
> for LJ-III, so I selected that driver and printed an old piece of
> artwork to my LJ-III. The output looked like I had sent a PostScript
> data stream to a non-Postcript printer .... lots of text. Do I have to
> select PostScript mode on the printer? How do I do that?

Probably through the front-panel menus. Later printers would
auto-select, but the LJIII may not have had that ability, or it may not
be enabled.

--
Warren Block * Rapid City, South Dakota * USA
 
Archived from groups: comp.periphs.printers (More info?)

>> Michael <NoSpam@att.net> wrote:
>> This printer does have an HP PostScript Cartridge Plus (C2089A)
>> plugged in but that's just fonts, isn't it?

No, the C2089A is the whole Ps2 interpreter, probably
including the base Ps fonts.

> Warren Block <wblock@wonkity.com> wrote:

> Looks like it's a full PostScript level 2 implementation.

There was also an HP 33439Q, which was Ps level 1.

> The printer has a 68000 processor running at 10 or 16 MHz,
> so it's not likely to interpret PostScript very quickly.

And it's probably slowed down even more by the font-slot
interface. That PS code may even be executing from the ctg.

> Try it on a reference document and time it.

And don't be too surprised if printing to file.ps,
distilling to PDF and then printing the PDF to the
LJ-III in PCL mode is actually faster for large jobs.

I used an LJ-3D with a C2089A briefly, and concluded
that about all I'd want to use the Ps for was for jobs
that wouldn't render properly in PCL mode.

--
Regards, Bob Niland mailto:name@ispname.tld
http://www.access-one.com/rjn email4rjn AT yahoo DOT com
NOT speaking for any employer, client or Internet Service Provider.
 
Archived from groups: comp.periphs.printers (More info?)

>How does one tell if a particular LJ-III has the "optional" PostScript
>feature? I have no docs. for the LJ-III that I picked up recently, and
>I see no menu item that appears to address PostScript. This printer
>does have an HP PostScript Cartridge Plus (C2089A) plugged in but that's
>just fonts, isn't it?

No, it's Postscript AND fonts. Does the cartridge have a blue or pink
graphic on it? Blue is Postscript v1, and pink is Postscript v2.

Raymond
 
Archived from groups: comp.periphs.printers (More info?)

Quadrajet1 wrote:
>
> >How does one tell if a particular LJ-III has the "optional" PostScript
> >feature? I have no docs. for the LJ-III that I picked up recently, and
> >I see no menu item that appears to address PostScript. This printer
> >does have an HP PostScript Cartridge Plus (C2089A) plugged in but that's
> >just fonts, isn't it?
>
> No, it's Postscript AND fonts. Does the cartridge have a blue or pink
> graphic on it? Blue is Postscript v1, and pink is Postscript v2.
>
> Raymond


I gues you'd call it pink. For sure it ain't blue. Says "PostScript",
lists 11 typefaces, but nothing about Postscript level.

I could swear I got this printer to list its PostScript "fonts" several
days ago while playing with menus but today I got nothing. After power
ON and near the end of Self Test, there is a brief message ... something
like "starting PostScript" ... which is replaced with the message
(something like) "starting PCL".
 
Archived from groups: comp.periphs.printers (More info?)

Bob Niland wrote:
>
> >> Michael <NoSpam@att.net> wrote:
> >> This printer does have an HP PostScript Cartridge Plus (C2089A)
> >> plugged in but that's just fonts, isn't it?
>
> No, the C2089A is the whole Ps2 interpreter, probably
> including the base Ps fonts.
>
> > Warren Block <wblock@wonkity.com> wrote:
>
> > Looks like it's a full PostScript level 2 implementation.
>
> There was also an HP 33439Q, which was Ps level 1.
>
> > The printer has a 68000 processor running at 10 or 16 MHz,
> > so it's not likely to interpret PostScript very quickly.
>
> And it's probably slowed down even more by the font-slot
> interface. That PS code may even be executing from the ctg.
>
> > Try it on a reference document and time it.
>
> And don't be too surprised if printing to file.ps,
> distilling to PDF and then printing the PDF to the
> LJ-III in PCL mode is actually faster for large jobs.
>
> I used an LJ-3D with a C2089A briefly, and concluded
> that about all I'd want to use the Ps for was for jobs
> that wouldn't render properly in PCL mode.
>
> --
> Regards, Bob Niland mailto:name@ispname.tld
> http://www.access-one.com/rjn email4rjn AT yahoo DOT com
> NOT speaking for any employer, client or Internet Service Provider.


I hear ya. My last laser, an IBM 4029, could be slow in PostScript, and
IIRC its controller ran faster than the one in this particular LJ-III
(10 MHz).
 
Archived from groups: comp.periphs.printers (More info?)

"Warren Block" <wblock@wonkity.com> wrote in message
news:slrnctbchv.esu.wblock@speedy.wonkity.com...
> Michael <NoSpam@att.net> wrote:
> > How does one tell if a particular LJ-III has the "optional" PostScript
> > feature? I have no docs. for the LJ-III that I picked up recently, and
> > I see no menu item that appears to address PostScript. This printer
> > does have an HP PostScript Cartridge Plus (C2089A) plugged in but that's
> > just fonts, isn't it?
>
> Looks like it's a full PostScript level 2 implementation. Genuine
> Adobe, even.
>
> The printer has a 68000 processor running at 10 or 16 MHz, so it's not
> likely to interpret PostScript very quickly. Try it on a reference
> document and time it. Then remove the C2089A and run the same document
> through Ghostscript on your computer, feeding PCL output to the printer.
>
> > I used to have an IBM 4029 w/ PostScript that I used with an old DOS
> > graphics package for laying out and printing PC board artwork. That
> > package's available driver selection offers only a Postscript drivers
> > for LJ-III, so I selected that driver and printed an old piece of
> > artwork to my LJ-III. The output looked like I had sent a PostScript
> > data stream to a non-Postcript printer .... lots of text. Do I have to
> > select PostScript mode on the printer? How do I do that?
>
> Probably through the front-panel menus. Later printers would
> auto-select, but the LJIII may not have had that ability, or it may not
> be enabled.
>
> --
> Warren Block * Rapid City, South Dakota * USA

You have to select either PCL5 or Postscript using the front panel controls.
Here is how you do it.

To change from PCL5 to Postscript (and back)

a.. Press <ON LINE> (and take machine off line)
b.. Press <Plus & Minus>, and while holding, press <ALT> and <RESET>
together and watch the LCD and let go when the desired mode is displayed.
With a modern PC, using ghostscript to do the conversion to PCL5 will be
much faster than printing to the Laserjet in postscript. You can try both
ways and measure it.

Regards
Barry
 
Archived from groups: comp.periphs.printers (More info?)

Baz wrote:
>
> "Warren Block" <wblock@wonkity.com> wrote in message
> news:slrnctbchv.esu.wblock@speedy.wonkity.com...
> > Michael <NoSpam@att.net> wrote:
> > > How does one tell if a particular LJ-III has the "optional" PostScript
> > > feature? I have no docs. for the LJ-III that I picked up recently, and
> > > I see no menu item that appears to address PostScript. This printer
> > > does have an HP PostScript Cartridge Plus (C2089A) plugged in but that's
> > > just fonts, isn't it?
> >
> > Looks like it's a full PostScript level 2 implementation. Genuine
> > Adobe, even.
> >
> > The printer has a 68000 processor running at 10 or 16 MHz, so it's not
> > likely to interpret PostScript very quickly. Try it on a reference
> > document and time it. Then remove the C2089A and run the same document
> > through Ghostscript on your computer, feeding PCL output to the printer.
> >
> > > I used to have an IBM 4029 w/ PostScript that I used with an old DOS
> > > graphics package for laying out and printing PC board artwork. That
> > > package's available driver selection offers only a Postscript drivers
> > > for LJ-III, so I selected that driver and printed an old piece of
> > > artwork to my LJ-III. The output looked like I had sent a PostScript
> > > data stream to a non-Postcript printer .... lots of text. Do I have to
> > > select PostScript mode on the printer? How do I do that?
> >
> > Probably through the front-panel menus. Later printers would
> > auto-select, but the LJIII may not have had that ability, or it may not
> > be enabled.
> >
> > --
> > Warren Block * Rapid City, South Dakota * USA
>
> You have to select either PCL5 or Postscript using the front panel controls.
> Here is how you do it.
>
> To change from PCL5 to Postscript (and back)
>
> a.. Press <ON LINE> (and take machine off line)
> b.. Press <Plus & Minus>, and while holding, press <ALT> and <RESET>
> together and watch the LCD and let go when the desired mode is displayed.
> With a modern PC, using ghostscript to do the conversion to PCL5 will be
> much faster than printing to the Laserjet in postscript. You can try both
> ways and measure it.
>
> Regards
> Barry



Many thanks for the magic key sequences. I gotta get the "book of
words" for this beast.
 
Archived from groups: comp.periphs.printers (More info?)

Baz wrote:
>
> "Warren Block" <wblock@wonkity.com> wrote in message
> news:slrnctbchv.esu.wblock@speedy.wonkity.com...
> > Michael <NoSpam@att.net> wrote:
> > > How does one tell if a particular LJ-III has the "optional" PostScript
> > > feature? I have no docs. for the LJ-III that I picked up recently, and
> > > I see no menu item that appears to address PostScript. This printer
> > > does have an HP PostScript Cartridge Plus (C2089A) plugged in but that's
> > > just fonts, isn't it?
> >
> > Looks like it's a full PostScript level 2 implementation. Genuine
> > Adobe, even.
> >
> > The printer has a 68000 processor running at 10 or 16 MHz, so it's not
> > likely to interpret PostScript very quickly. Try it on a reference
> > document and time it. Then remove the C2089A and run the same document
> > through Ghostscript on your computer, feeding PCL output to the printer.
> >
> > > I used to have an IBM 4029 w/ PostScript that I used with an old DOS
> > > graphics package for laying out and printing PC board artwork. That
> > > package's available driver selection offers only a Postscript drivers
> > > for LJ-III, so I selected that driver and printed an old piece of
> > > artwork to my LJ-III. The output looked like I had sent a PostScript
> > > data stream to a non-Postcript printer .... lots of text. Do I have to
> > > select PostScript mode on the printer? How do I do that?
> >
> > Probably through the front-panel menus. Later printers would
> > auto-select, but the LJIII may not have had that ability, or it may not
> > be enabled.
> >
> > --
> > Warren Block * Rapid City, South Dakota * USA
>
> You have to select either PCL5 or Postscript using the front panel controls.
> Here is how you do it.
>
> To change from PCL5 to Postscript (and back)
>
> a.. Press <ON LINE> (and take machine off line)
> b.. Press <Plus & Minus>, and while holding, press <ALT> and <RESET>
> together and watch the LCD and let go when the desired mode is displayed.
> With a modern PC, using ghostscript to do the conversion to PCL5 will be
> much faster than printing to the Laserjet in postscript. You can try both
> ways and measure it.
>
> Regards
> Barry


Uh ... where the heck is the <Alt> key?? I've got:
On Line
Form Feed
Continue/Reset
Print Forms/Test
Menu
Enter/Reset Menu
+
-
 
Archived from groups: comp.periphs.printers (More info?)

"Michael" <NoSpam@att.net> wrote in message
news:41D62085.961A723A@att.net...
> Baz wrote:
> >
> > "Warren Block" <wblock@wonkity.com> wrote in message
> > news:slrnctbchv.esu.wblock@speedy.wonkity.com...
> > > Michael <NoSpam@att.net> wrote:
> > > > How does one tell if a particular LJ-III has the "optional"
PostScript
> > > > feature? I have no docs. for the LJ-III that I picked up recently,
and
> > > > I see no menu item that appears to address PostScript. This printer
> > > > does have an HP PostScript Cartridge Plus (C2089A) plugged in but
that's
> > > > just fonts, isn't it?
> > >
> > > Looks like it's a full PostScript level 2 implementation. Genuine
> > > Adobe, even.
> > >
> > > The printer has a 68000 processor running at 10 or 16 MHz, so it's not
> > > likely to interpret PostScript very quickly. Try it on a reference
> > > document and time it. Then remove the C2089A and run the same
document
> > > through Ghostscript on your computer, feeding PCL output to the
printer.
> > >
> > > > I used to have an IBM 4029 w/ PostScript that I used with an old DOS
> > > > graphics package for laying out and printing PC board artwork. That
> > > > package's available driver selection offers only a Postscript
drivers
> > > > for LJ-III, so I selected that driver and printed an old piece of
> > > > artwork to my LJ-III. The output looked like I had sent a
PostScript
> > > > data stream to a non-Postcript printer .... lots of text. Do I have
to
> > > > select PostScript mode on the printer? How do I do that?
> > >
> > > Probably through the front-panel menus. Later printers would
> > > auto-select, but the LJIII may not have had that ability, or it may
not
> > > be enabled.
> > >
> > > --
> > > Warren Block * Rapid City, South Dakota * USA
> >
> > You have to select either PCL5 or Postscript using the front panel
controls.
> > Here is how you do it.
> >
> > To change from PCL5 to Postscript (and back)
> >
> > a.. Press <ON LINE> (and take machine off line)
> > b.. Press <Plus & Minus>, and while holding, press <ALT> and <RESET>
> > together and watch the LCD and let go when the desired mode is
displayed.
> > With a modern PC, using ghostscript to do the conversion to PCL5 will be
> > much faster than printing to the Laserjet in postscript. You can try
both
> > ways and measure it.
> >
> > Regards
> > Barry
>
>
> Uh ... where the heck is the <Alt> key?? I've got:
> On Line
> Form Feed
> Continue/Reset
> Print Forms/Test
> Menu
> Enter/Reset Menu
> +
> -

Whoops, sorry Michael, I missed yours was a III not a IIIP like mine.. The
cartridge can be used on models III, IIID and IIIP.

However I have a C2089A manual and it gives the following instructions:

To switch the printer language using the control panel keys, do the
following:
HP Laserjet III and IIID Printers
1. Make sure the printer is not processing data
2. Press the <ON LINE> key to take the printer offline
3. While holding down the <+> key, press the <RESET> key.
4. The printer will automatically return online
Your printer will now print in the other printer language.

Sorry for giving the instructions for the wrong machine.

If you are interested in the C2089A manual, email me at
xxbarxvicx1x39@swiftxdsl.com.au (with all the x's removed) with your
address. Most of it talks about the old DOS days. In my opinion everything
you really need to know these days is how to manually change from PCL to
Postscript. I haven't used my postscript option for some time, but its nice
to have available.

Regards
Barry
 
Archived from groups: comp.periphs.printers (More info?)

On Fri, 31 Dec 2004 16:55:00 -0600, Bob Niland <email4rjn@yahoo.com>
wrote:

>>> Michael <NoSpam@att.net> wrote:
>>> This printer does have an HP PostScript Cartridge Plus (C2089A)
>>> plugged in but that's just fonts, isn't it?
>
>No, the C2089A is the whole Ps2 interpreter, probably
>including the base Ps fonts.

The PS SIMM in my HP4 has a copyright notice for the Linotype fonts,
as well as Adobe. I think any PS add on will include at least the
"LaserWriter" 35 fonts, or clones.

>> Warren Block <wblock@wonkity.com> wrote:
>
>> Looks like it's a full PostScript level 2 implementation.
>
>There was also an HP 33439Q, which was Ps level 1.
>
>> The printer has a 68000 processor running at 10 or 16 MHz,
>> so it's not likely to interpret PostScript very quickly.
>
>And it's probably slowed down even more by the font-slot
>interface. That PS code may even be executing from the ctg.

I had an LJIII with a different make of PS cartridge (Pacific Page),
it also required an additional RAM card (built in RAM was 500k, the
card was 4M), and I'm pretty sure the PS was executed from the RAM.

>> Try it on a reference document and time it.
>
>And don't be too surprised if printing to file.ps,
>distilling to PDF and then printing the PDF to the
>LJ-III in PCL mode is actually faster for large jobs.

I found that too. The cartridge was good for compatibility with pure
DOS PS, but I'd already set up Printfile (freeware) to process PS to
PCL, first using GhostScript, which was fairly fast, second using
Distiller and Acroreader to print -- this gave better quality
printouts than GS. One plus of the cartridge was that you could load
fonts in RAM, and mostly text jobs would print fairly fast.

If you do use it in PCL mode, note that it probably has more RAM than
the default, (should show if you print a status page) so put that in
your printer properties so it can be used in PCL mode too.
 
Archived from groups: comp.periphs.printers (More info?)

Alan wrote:
>
> On Fri, 31 Dec 2004 16:55:00 -0600, Bob Niland <email4rjn@yahoo.com>
> wrote:
>
> >>> Michael <NoSpam@att.net> wrote:
> >>> This printer does have an HP PostScript Cartridge Plus (C2089A)
> >>> plugged in but that's just fonts, isn't it?
> >
> >No, the C2089A is the whole Ps2 interpreter, probably
> >including the base Ps fonts.
>
> The PS SIMM in my HP4 has a copyright notice for the Linotype fonts,
> as well as Adobe. I think any PS add on will include at least the
> "LaserWriter" 35 fonts, or clones.
>
> >> Warren Block <wblock@wonkity.com> wrote:
> >
> >> Looks like it's a full PostScript level 2 implementation.
> >
> >There was also an HP 33439Q, which was Ps level 1.
> >
> >> The printer has a 68000 processor running at 10 or 16 MHz,
> >> so it's not likely to interpret PostScript very quickly.
> >
> >And it's probably slowed down even more by the font-slot
> >interface. That PS code may even be executing from the ctg.
>
> I had an LJIII with a different make of PS cartridge (Pacific Page),
> it also required an additional RAM card (built in RAM was 500k, the
> card was 4M), and I'm pretty sure the PS was executed from the RAM.

I still don't know how to get this LJ-3 into PS mode. Another poster
very nicely spelled out the procedure for doing this ....... all very
well except it includes pressing the "<Alt>" key. I see no key marked
<Alt>, so the procedure was not useful.

Base mem. on a LJ-3 is 1 Meg. Mine is expanded with a 4 Meg card that
is populated with 2 Meg, so it has 3 MB total. That ain't much; I think
my IBM4029 w/ PS had 6 MB yet I overran it many, many times.
 
Archived from groups: comp.periphs.printers (More info?)

On Mon, 03 Jan 2005 15:45:15 GMT, Michael <NoSpam@att.net> wrote:

>Alan wrote:

>> I had an LJIII with a different make of PS cartridge (Pacific Page),
>> it also required an additional RAM card (built in RAM was 500k, the
>> card was 4M), and I'm pretty sure the PS was executed from the RAM.
>
>I still don't know how to get this LJ-3 into PS mode. Another poster
>very nicely spelled out the procedure for doing this ....... all very
>well except it includes pressing the "<Alt>" key. I see no key marked
><Alt>, so the procedure was not useful.

With my Pacific cart, you switched modes with a PCL command. Probably
not applicable, but these are:
to PCL mode: <ESC>&l1057.32259J
to PS mode: <ESC>&l5257.1058J

I Googled on C2089A and found a few possibly useful things.
Search groups.google.com for
"HP III/IIID PostScript Cartridge Plus - Turning Off Start Page"
and you find a couple of messages:
"press the control panel's Menu button for a few seconds to reach the
second Configuration menu level, tap the Menu button ..."
-- can you get to this "second" menu?

And another post for a software archive listed this file:

99957 1995/10/25 09:22 /printers/software/psplus.exe
HP LaserJet printer PostScript Cartridge Plus (C2089A) PCL/PostScript
DOS device driver for language switching between PCL and PostScript.

This should be on the LEO archive, at
<http://www.leo.org/information/computer/software/msdos/index_en.html>,
but it doesn't seem to respond now.
Also found a link
<http://kd002.kud.com/ftp/pub/hardware/hp/psplus.exe>, but this also
times out.

Maybe give them a few tries, or email the webmasters.

>Base mem. on a LJ-3 is 1 Meg. Mine is expanded with a 4 Meg card that
>is populated with 2 Meg, so it has 3 MB total. That ain't much; I think
>my IBM4029 w/ PS had 6 MB yet I overran it many, many times.

The LJIII is 300 dpi, I think the 4029 is 600 dpi, so 3MB can cover
more than the same area.

~~~~ Alan
 
Archived from groups: comp.periphs.printers (More info?)

"Michael" <NoSpam@att.net> wrote in message
news:41D96887.716AE1D7@att.net...
> Alan wrote:
> >
> > On Fri, 31 Dec 2004 16:55:00 -0600, Bob Niland <email4rjn@yahoo.com>
> > wrote:
> >
> > >>> Michael <NoSpam@att.net> wrote:
> > >>> This printer does have an HP PostScript Cartridge Plus (C2089A)
> > >>> plugged in but that's just fonts, isn't it?
> > >
> > >No, the C2089A is the whole Ps2 interpreter, probably
> > >including the base Ps fonts.
> >
> > The PS SIMM in my HP4 has a copyright notice for the Linotype fonts,
> > as well as Adobe. I think any PS add on will include at least the
> > "LaserWriter" 35 fonts, or clones.
> >
> > >> Warren Block <wblock@wonkity.com> wrote:
> > >
> > >> Looks like it's a full PostScript level 2 implementation.
> > >
> > >There was also an HP 33439Q, which was Ps level 1.
> > >
> > >> The printer has a 68000 processor running at 10 or 16 MHz,
> > >> so it's not likely to interpret PostScript very quickly.
> > >
> > >And it's probably slowed down even more by the font-slot
> > >interface. That PS code may even be executing from the ctg.
> >
> > I had an LJIII with a different make of PS cartridge (Pacific Page),
> > it also required an additional RAM card (built in RAM was 500k, the
> > card was 4M), and I'm pretty sure the PS was executed from the RAM.
>
> I still don't know how to get this LJ-3 into PS mode. Another poster
> very nicely spelled out the procedure for doing this ....... all very
> well except it includes pressing the "<Alt>" key. I see no key marked
> <Alt>, so the procedure was not useful.
>
> Base mem. on a LJ-3 is 1 Meg. Mine is expanded with a 4 Meg card that
> is populated with 2 Meg, so it has 3 MB total. That ain't much; I think
> my IBM4029 w/ PS had 6 MB yet I overran it many, many times.

Hi Michael,

Sorry about the wrong printer type. Did you try the suggestion in my second
post on 2-1-2005

Regards
Barry
 
Archived from groups: comp.periphs.printers (More info?)

Baz wrote:
> Sorry about the wrong printer type. Did you try the suggestion in my second
> post on 2-1-2005
>
> Regards
> Barry


I didn't see that post, Barry, but I just looked it up on Deja and
copied the relevant part. Will give it a try. Thanks for going the
extra mile for me. And for offering the C2089A manual, which I think
I'll pass on. I would like to find a LJ-2/3 Combined Maint. Manual
however.

Michael
 
Archived from groups: comp.periphs.printers (More info?)

Alan wrote:

> The LJIII is 300 dpi, I think the 4029 is 600 dpi, so 3MB can cover
> more than the same area.

Oh yeah! I forgot about the difference in resolution. 3 MB mem.
suddenly sounds not quite so bad. This is good also because I probably
won't be able to find suitable chips at a reasonable price and in a
reasonable time.

Thanks for all your input, Alan.

Michael
 
Archived from groups: comp.periphs.printers (More info?)

Baz wrote:
> Hi Michael,
>
> Sorry about the wrong printer type. Did you try the suggestion in my second
> post on 2-1-2005
>
> Regards
> Barry


Just gave it a try. Display says "POSTSCRIPT READY". Thanks again,
Barry.

Michael
 
Archived from groups: comp.periphs.printers (More info?)

On Wed, 05 Jan 2005 06:43:35 GMT, Michael <NoSpam@att.net> wrote:

> I would like to find a LJ-2/3 Combined Maint. Manual
>however.
>
>Michael

Excellent diagrams at TPW:
<http://www.printerworks.com/Printers/Laser-Printers.html>

Also, the Apple LaserWriter II is mostly identical except for the
logic and the outer covers. So its manual is a very good guide for
repair, available at <http://www.whoopis.com/computer_repair/>:
 
Archived from groups: comp.periphs.printers (More info?)

Alan wrote:
>
> On Wed, 05 Jan 2005 06:43:35 GMT, Michael <NoSpam@att.net> wrote:
>
> > I would like to find a LJ-2/3 Combined Maint. Manual
> >however.
> >
> >Michael
>
> Excellent diagrams at TPW:
> <http://www.printerworks.com/Printers/Laser-Printers.html>
>
> Also, the Apple LaserWriter II is mostly identical except for the
> logic and the outer covers. So its manual is a very good guide for
> repair, available at <http://www.whoopis.com/computer_repair/>:


Thanks for that, Alan.
 
You must log in or register to reply here.

TRENDING THREADS

Latest posts

Moderators online

Share this page

COMPANY
RESOURCES
FOLLOW
Top Bottom