I Guess I screwed the wrong screws!

Fetito

Reputable
Jul 2, 2019
52
0
4,530
On my new Asus ROG Strix G15 G513RM I added a second SSD, but I somehow, I messed up the order of the screws.


Since probably I just killed the warranty, I would like to ask, if there is a good way to hide the hole and to protect the laptop.

  1. Is a sticker enough? Are there other solutions?
  2. How do I get the original screw "matrix" to put the screws back in the intended order? I have checked the PDF-manual and it does not mention this.
  3. Is this a warranty case (the laptop is 3 days old!) or can I pay Asus to replace the plastic case?
Thank you!
 
Is a sticker enough?
That would be cheapest "fix".

Is this a warranty case (the laptop is 3 days old!)
Asus (manufacturer) is not responsible for your mistake. So, No. It doesn't fall under warranty.

or can I pay Asus to replace the plastic case?
Contact Asus and ask them. Maybe they are willing to take in your warranty voided laptop for repairs, when you pay for the whole repairs + shipping.
 
  • Like
Reactions: Fetito
Thanks. How do I get the original screw "matrix" to put the screws back in the intended order? I have checked the PDF-manual and it does not mention this.
 
You could continue to check online for your model to see if there is a blown up diagram of it somewhere.

Any time I take apart a laptop I keep a large open area and always start at the same point, say to the left of the display hinge, etc. When you unscrew, set the screw down in the orientation you start with. Stay consistent on which way you go around (clock/counter) and set each screw out in that open area in order as you remove them. I also recommend using something like a food tray/platter with an edge and keep your cat out of the room (if that applies).

In the case that you have already mixed them up, the only thing to do is pay really close attention as you are screwing them back in and not applying undue force when they aren't shouldered up.
I tend to agree that a sticker should work fine here. You could check, JB Weld might be about the same color as that case if you wanted to actually close the hole.
 
  • Like
Reactions: Fetito
JB Weld to me would be a very last resort if a resort at all.

Four immediate reasons:

1) Getting the color to match is quite problematic.

2) Even if the color matches the glue is messy to apply and you will never achieve a smooth looking finish.

3) Removing the glue later will cause more discoloration and damage.

4) Any glue that works its' way down inside via the hole is likely to glue other things into place from the inside.
That would be a real nightmare.

= = = =

That all said:

Are the screws all the same size? Did the hole result from putting a larger screw into a smaller hole?

I suggest adding a couple more photographs as applicable to show what you are working with and what was done.

In the end if all you end up with is a blemish on a working/fully functioning new laptop just leave things alone.

Other than, perhaps, covering the hole with a small piece of some removable label or sticker.

And count yourself lucky.
 
  • Like
Reactions: Fetito
Yes, the the hole result from putting a larger screw into a smaller hole.

The laptop works perfectly, it is just that I caused a hole by putting a larger screw into the wrong place. And a "pimple" on the left side.
And yes, I count myself lucky. I am willing to pay Asus for a new plastic case above.

And I would like to get a matrix on how the screws should have been assigned. Somehow I mixed them. I have even read the PDF-manual regarding which screw belongs to which hole, but there was no info in the PDF-file. My fault... I should have put the screws in order.

Here is a link on from the left side:

View: https://imgur.com/7ZD84gk
 
All in all then - leave well enough alone including paying for a new case.

Only a matter of time until any case picks up its' first ding, scratch, dent, etc..

The existing case has a bit of a headstart.....

Plus replacing the case is just another opportunity for Mr. Murphy to make an appearance.

Cover the blemish with removable tape or some appealing sticker.

As for documentation regarding screws, procedures etc. all that gets expensive and an error within may lead to lawsuits. The less said the better is more the norm nowadays.

Key is to be able to blame the end-users.

Cynicism conceded.

Glad to hear the laptops works. Take a sigh of relief and move on.
 
  • Like
Reactions: Fetito