Ok so specs are:
HP Pavilion 570-p026na
Willow 2 Motherboard
AMD A12-9800 cpu with Radeon r7 integrated in it.
2x DDR4 8GB sticks 1,333 GHz.
130 SSD San Disk with fresh win 10 on it.
3T HDD for ''stuff''...
Story time, the PSU the PC had was 180W, i changed it to a 500W one because i bought a nVidia GT730 4GB DDR5 graphics card. I installed that card, and nothing seemed to make it work, i kept getting no signal from the card or integrated gpu when the card was inside the motherboard. I tried unplugging and 1 minute of holding down the power button, resetting CMOS via battery removal, resetting CMOS via jumper, resetting BIOS to factory settings from within the BIOS, every single trick in the book, nothing worked (yes, i disabled and uninstalled the integrated graphics card inside the CPU). During this ''trying'' what happened was i had the card installed on the motherboard and the PC was on...the windows actually boots up, i can hear the start up sound and all, just no signal whatsoever...so after like 6 hours of intense research and painful stress, i went for a cigarette, when i came back, bingo, the screen was on, and NOT ONLY THAT, but the nVidia GT730 driver was installed aswell in the device manager...WHICH I DID NOT INSTALL...there was nothing in the Display Adapter tab, as i disabled everything, uninstalled it, etc...SO BASICALLY IT ALL updated itself and installed...still confused on how....
The problem is during booting up, i see nothing, i just wake up with windows on after like 20 seconds, all runs smooth. I cannot enter bios (can't see POST message, nothing happens if i press F10, F2, F6, F8, DEL, etc... then if i remove the card and start the PC i can see the POST, i can press ESC and it takes me to a small menu, from which i can go to BIOS, BOOT MENU, etc...) I had to reinstall windows as it was on my HDD not on my SSD and i needed to remove the HDD for a project. I had to remove the graphics card so that i could boot the instalation of windows 10 from the USB.... all well, i installed the new windows 10, PC booted up, everything works now....BUT my graphics card....so it was working yesterday, but now i basically need to find a way to instal the graphics drivers without the card inside the motherboard as it wont give any signal at all....ANY IDEEAS?????
Before posting i repeat myself...i tried the following 1> CMOS reset 2>BIOS reset 3>Disabling on board graphics 4> Uninstalling on board graphics 5> One minute of power button (unplugged) 6> Different BIOS settings (there's not much i can change in bios on this particular set up, i can provide pictures if needed)....... IF ANY OF YOU have any ideea, let me know....
HP Pavilion 570-p026na
Willow 2 Motherboard
AMD A12-9800 cpu with Radeon r7 integrated in it.
2x DDR4 8GB sticks 1,333 GHz.
130 SSD San Disk with fresh win 10 on it.
3T HDD for ''stuff''...
Story time, the PSU the PC had was 180W, i changed it to a 500W one because i bought a nVidia GT730 4GB DDR5 graphics card. I installed that card, and nothing seemed to make it work, i kept getting no signal from the card or integrated gpu when the card was inside the motherboard. I tried unplugging and 1 minute of holding down the power button, resetting CMOS via battery removal, resetting CMOS via jumper, resetting BIOS to factory settings from within the BIOS, every single trick in the book, nothing worked (yes, i disabled and uninstalled the integrated graphics card inside the CPU). During this ''trying'' what happened was i had the card installed on the motherboard and the PC was on...the windows actually boots up, i can hear the start up sound and all, just no signal whatsoever...so after like 6 hours of intense research and painful stress, i went for a cigarette, when i came back, bingo, the screen was on, and NOT ONLY THAT, but the nVidia GT730 driver was installed aswell in the device manager...WHICH I DID NOT INSTALL...there was nothing in the Display Adapter tab, as i disabled everything, uninstalled it, etc...SO BASICALLY IT ALL updated itself and installed...still confused on how....
The problem is during booting up, i see nothing, i just wake up with windows on after like 20 seconds, all runs smooth. I cannot enter bios (can't see POST message, nothing happens if i press F10, F2, F6, F8, DEL, etc... then if i remove the card and start the PC i can see the POST, i can press ESC and it takes me to a small menu, from which i can go to BIOS, BOOT MENU, etc...) I had to reinstall windows as it was on my HDD not on my SSD and i needed to remove the HDD for a project. I had to remove the graphics card so that i could boot the instalation of windows 10 from the USB.... all well, i installed the new windows 10, PC booted up, everything works now....BUT my graphics card....so it was working yesterday, but now i basically need to find a way to instal the graphics drivers without the card inside the motherboard as it wont give any signal at all....ANY IDEEAS?????
Before posting i repeat myself...i tried the following 1> CMOS reset 2>BIOS reset 3>Disabling on board graphics 4> Uninstalling on board graphics 5> One minute of power button (unplugged) 6> Different BIOS settings (there's not much i can change in bios on this particular set up, i can provide pictures if needed)....... IF ANY OF YOU have any ideea, let me know....