[SOLVED] Intel coolers

Nov 11, 2019
20
3
15
0
Hi so im making a major upgrade to my PC (full motherboard and CPU swap), I am replacing my MB with a MSI MPG Z390M so i can get a 9th gen I7. Though the only problem is that it does not come with a cooler. Right now I have a I5 6500 and its cooler and i want to get an I7 9700K (I am not overclocking) will the I5's cooler be ok on the I7 9700K or will i have to buy a seperate one?

Thank you to everyone that takes there time out of there day to read this!:)
 
For normal usage, no, the intel cooler will not do the job.
But, I expect you are anxious to see how your new processor is going to work.
I think you can use the stock cooler for that purpose, or until you buy a stronger cooler.
Yes, it will spin up and be noisy.

Perhaps this can help:

----------------how to mount the stock Intel cooler--------------

The stock Intel cooler can be tricky to install.
A poor installation will result in higher cpu temperatures.
If properly mounted, you should expect temperatures at idle to be 10-15c. over ambient.

To mount the Intel stock cooler properly, place the motherboard on top of the foam or cardboard backing that was packed with the motherboard.
The stock cooler will come with paste pre applied, it looks like three grey strips.
The 4 push pins should come in the proper position for installation, that is with the pins rotated in the opposite direction of the arrow,(clockwise)
and pulled up as far as they can go.
Take the time to play with the pushpin mechanism until you know how they work.

Orient the 4 pins so that they are exactly over the motherboard holes.
If one is out of place, you will damage the pins which are delicate.
Push down on a DIAGONAL pair of pins at the same time. Then the other pair.

When you push down on the top black pins, it expands the white plastic pins to fix the cooler in place.

If you do them one at a time, you will not get the cooler on straight.
Lastly, look at the back of the motherboard to verify that all 4 pins are equally through the motherboard, and that the cooler is on firmly.
This last step must be done, which is why the motherboard should be out of the case to do the job. Or you need a case with a opening that lets you see the pins.
It is possible to mount the cooler with the motherboard mounted in the case, but you can then never be certain that the push pins are inserted properly
unless you can verify that the pins are through the motherboard and locked.

If you should need to remove the cooler, turn the pins counter clockwise to unlock them.
You will need to clean off the old paste and reapply new if you ever take the cooler off.
Clean off old paste with alcohol and a lint free paper like a coffee filter.
Apply new paste sparingly. A small rice sized drop in the center will spread our under heat and pressure.
Too much paste is bad, it will act as an insulator.
It is hard to use too little.

----------------------------------------------------------------------------------
 
Nov 11, 2019
20
3
15
0
For normal usage, no, the intel cooler will not do the job.
But, I expect you are anxious to see how your new processor is going to work.
I think you can use the stock cooler for that purpose, or until you buy a stronger cooler.
Yes, it will spin up and be noisy.

Perhaps this can help:

----------------how to mount the stock Intel cooler--------------

The stock Intel cooler can be tricky to install.
A poor installation will result in higher cpu temperatures.
If properly mounted, you should expect temperatures at idle to be 10-15c. over ambient.

To mount the Intel stock cooler properly, place the motherboard on top of the foam or cardboard backing that was packed with the motherboard.
The stock cooler will come with paste pre applied, it looks like three grey strips.
The 4 push pins should come in the proper position for installation, that is with the pins rotated in the opposite direction of the arrow,(clockwise)
and pulled up as far as they can go.
Take the time to play with the pushpin mechanism until you know how they work.

Orient the 4 pins so that they are exactly over the motherboard holes.
If one is out of place, you will damage the pins which are delicate.
Push down on a DIAGONAL pair of pins at the same time. Then the other pair.

When you push down on the top black pins, it expands the white plastic pins to fix the cooler in place.

If you do them one at a time, you will not get the cooler on straight.
Lastly, look at the back of the motherboard to verify that all 4 pins are equally through the motherboard, and that the cooler is on firmly.
This last step must be done, which is why the motherboard should be out of the case to do the job. Or you need a case with a opening that lets you see the pins.
It is possible to mount the cooler with the motherboard mounted in the case, but you can then never be certain that the push pins are inserted properly
unless you can verify that the pins are through the motherboard and locked.

If you should need to remove the cooler, turn the pins counter clockwise to unlock them.
You will need to clean off the old paste and reapply new if you ever take the cooler off.
Clean off old paste with alcohol and a lint free paper like a coffee filter.
Apply new paste sparingly. A small rice sized drop in the center will spread our under heat and pressure.
Too much paste is bad, it will act as an insulator.
It is hard to use too little.

----------------------------------------------------------------------------------
Thanks for the Reply and help:D would a (be quiet! Dark Rock Pro 4, BK022, 250W TDP, CPU Cooler) be a suitable cooler for the I7 9700k?
 

ASK THE COMMUNITY

TRENDING THREADS