Question LED Lights

[kiwis]

I have a Aorus B450 Pro WIFI board (manual below) and a Phantek P360X case. (manual also below)

I'm not sure how to plug in the front LED lights (plugs on left of image here).

Any help would be appreciated.

https://www.tweaktown.com/reviews/9184/phanteks-eclipse-p360x-mid-tower-chassis-review/index5.html


http://www.phanteks.com/assets/manuals/PH-EC360X.pdf
http://download.gigabyte.us/FileList/Manual/mb_manual_b450-aorus-pro-wifi_1001_e.pdf

 

[extreme_noob]

Tweaktown article said: "The front panel cables are as follows (left to right):

- ARGB 3-pin output cable (3-pin standard & 3-pin specialized header)

- SATA power lead for RGB control

- HD Audio connector

- USB 3.2 Gen 1, 20-pin connector

- Power Switch connector

- 3-pin ARGB sync connector (to sync with the motherboard)"

Don't plug the 3 pin output cable into anything unless you want to sync an RGB strip to the front panel

Plug the sata power into the appropriate cable from your PSU

Plug HD Audio into the motherboard where it should say "HD Audio". Header is shown in motherboard manual on the bottom left of the motherboard.

Plug the USB 3.2 Gen 1 connector into the motherboard. Header is shown in the motherboard manual on the bottom right, second from the right.

Plug the Power Switch connector into the motherboard. Header is shown in the manual on the bottom right corner, and the manual should also tell you which two pins to plug it into.

Plug the 3 pin ARGB connector (which is for the LEDs) into the motherboard. The headers for this are listed as D_LED1 and D_LED2, positioned at bottom middle and top right, respectively.

 

[kiwis]

- ARGB 3-pin output cable (3-pin standard & 3-pin specialized header)

Don't plug the 3 pin output cable into anything unless you want to sync an RGB strip to the front panel

Plug the 3 pin ARGB connector (which is for the LEDs) into the motherboard. The headers for this are listed as D_LED1 and D_LED2, positioned at bottom middle and top right, respectively.

Page 11: Location 9 & 10.

http://download.gigabyte.us/FileList/Manual/mb_manual_b450-aorus-pro-wifi_1001_e.pdf

These are pins and the plug has pins also.

Is that normal?

 

[extreme_noob]

Page 11: Location 9 & 10.

http://download.gigabyte.us/FileList/Manual/mb_manual_b450-aorus-pro-wifi_1001_e.pdf

These are pins and the plug has pins also.

Is that normal?

You sure its the same page 11? The one I see is rear IO.

 

[kiwis]

No, page 13.

 

[extreme_noob]

No, page 13.

Plug it into location 9, and location 10 is used to select voltage. Leave it, as the default is 5V.

 

[kiwis]

Plug it into location 9, and location 10 is used to select voltage. Leave it, as the default is 5V.

You can see my plugs have pins, the very very left just has a cover on it.

The board also has pins if you zoom right in

https://www.newegg.com/gigabyte-b450-aorus-pro-wifi/p/N82E16813145082

 

[extreme_noob]

You can see my plugs have pins, the very very left just has a cover on it.

The board also has pins if you zoom right in

https://www.newegg.com/gigabyte-b450-aorus-pro-wifi/p/N82E16813145082

Ignore the leftmost cable, plug the rightmost cable into location 9, as it is the RGB cable

 

[kiwis]

Ignore the leftmost cable, plug the rightmost cable into location 9, as it is the RGB cable

So the cable on the left, both plugs ignore them. Just use the plug on the very right of the image for LED.

I've got that plugged into my LED pace I don't have any front lights on my case

 

[extreme_noob]

So the cable on the left, both plugs ignore them. Just use the plug on the very right of the image for LED.

I've got that plugged into my LED pace I don't have any front lights on my case

Have you plugged sata power into the sata cable (Second from the left)?