Marvell vct not working

Toggle sidebar Toggle sidebar
G

Guest

Guest
Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

i have an asus k8v-x motherboard with a built in Marvell 88E8001GbLAN
chip. The specs on the asus site says that the mobo supports the
virtual cable tester. But when i lauched the exe it won't allow to run
it. The "run" button is greyed out or lock or something. Should i
contact asus or the store where i bought the mobo from or is this a
software problem?
 
Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

You must not be connected to a hub or other device that makes the link
active. The DSP must not be active for the test to work. The VCT help
file describes the resultant diagnostic messages after you run the utility.


PB

Brandon wrote:
> i have an asus k8v-x motherboard with a built in Marvell 88E8001GbLAN
> chip. The specs on the asus site says that the mobo supports the
> virtual cable tester. But when i lauched the exe it won't allow to run
> it. The "run" button is greyed out or lock or something. Should i
> contact asus or the store where i bought the mobo from or is this a
> software problem?
>
 
Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

In article <1117481671.963113.184080@o13g2000cwo.googlegroups.com>,
"Brandon" <trinimondem@gmail.com> wrote:

> i have an asus k8v-x motherboard with a built in Marvell 88E8001GbLAN
> chip. The specs on the asus site says that the mobo supports the
> virtual cable tester. But when i lauched the exe it won't allow to run
> it. The "run" button is greyed out or lock or something. Should i
> contact asus or the store where i bought the mobo from or is this a
> software problem?

Does VCT need some driver to be installed first ?

Paul
 
Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

I am connected to a hub, and i am sure the hub is working because i get
a ip address from it. But its only a 10base hub, does that matter?
 
Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

Paul wrote:
> In article <1117481671.963113.184080@o13g2000cwo.googlegroups.com>,
> "Brandon" <trinimondem@gmail.com> wrote:
>
> > i have an asus k8v-x motherboard with a built in Marvell 88E8001GbLAN
> > chip. The specs on the asus site says that the mobo supports the
> > virtual cable tester. But when i lauched the exe it won't allow to run
> > it. The "run" button is greyed out or lock or something. Should i
> > contact asus or the store where i bought the mobo from or is this a
> > software problem?
>
> Does VCT need some driver to be installed first ?
>
> Paul

Yes it does, but i alrady installed the drivers. In fact the VCT
software i am using came with the drivers that i downloaded from asus
website.
 
Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

I am connected to a hub, and i am sure the hub is working because i get
a ip address from it. But its only a 10base hub, does that matter?
 
Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

i disconnected the calbe from my hub and then i laucnhed the calbe
tester and i was able to test it perfectly.
 
You must log in or register to reply here.

TRENDING THREADS

Latest posts

Moderators online

Share this page

COMPANY
RESOURCES
FOLLOW
Top Bottom