Need help resolving K100 problems

G

Guest

Guest
Archived from groups: comp.sys.hp.hpux,comp.sys.hp.hardware (More info?)

I am having a heck of a time trying to discern what is wrong with one of my
K100s

When attempting to install HP-UX, the system boots, but eventually displays
the following on the console:

***

Booting...
Boot IO Dependent Code (IODC) revision 0


HARD Booted.

ISL Revision A.00.43 Apr12, 2000

ISL booting hpux (;0):INSTALL

Boot
: disk(8/12/5.2.0.0.0.0.0;0):INSTALL
9707284 + 1122304 + 691712 start 0x14d568
FLT CBFB
******* Unexpected HPMC. Processor HPA 0xfffa0000 *******
GENERAL REGISTERS:
r00/07 00000000 0010C800 00452F94 02A46800 00000089 00000000 00000000
02971280
r08/15 00000001 00000002 00000003 0FD1BE2C 0014D568 FFFFFFFF 00000801
000331D0
r16/23 00000001 00030720 00000008 FFB40838 00000008 00000001 00081003
FFB40800
r24/31 00000000 00000045 FFB40845 00A73268 00000000 00000038 7FFF0CB0
00081003
CONTROL REGISTERS:
sr0/7 00000000 00000000 00000000 00000000 00000000 0000224D 00002247
00000000
pcq 00000000.0010CF84 00000000.0010CF88 isr = 00000000 ior = 00452F94
pid1/4 0000 0000 0000 0000 ipsw = 0004000F iva = 00029800 sar = 0F ccr = C0
tr0/7 00982AA8 00035800 FFFFFFF0 00000000 01830930 15F168E5 0009BB68
7FFF0BB8
rctr = 00000000 itmr = 160B5F84 eiem = FFFFFFF0 eirr = 80000008 iir =
E840C002
cr1/7 00000000 00000000 00000000 00000000 00000000 00000000 00000000
MACHINE CHECK PARAMETERS:
Check Type = 20000000 CPU STATE = 9E000004 Cache Check = 00000000
TLB Check = 00000000 Bus Check = 0020000C PIM State = ? SIU Status =
????????
Detected by 00000000 Assists = 00000000 Processor = 00000000
Assist ID = 00000000 Slave Addr = FFFA0000 Master Addr = 00000000


trap type 1 (HPMC), pcsq.pcoq = 0.10cf84, isr.ior = 0.452f94
@(#) $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c
'Vw
for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108'
Wed N
ov 8 19:05:38 PST 2000 $High-priority machine check: (display==0xd910,
flags==0
x0)
* CPU State 0x9e000004
* Detected By 0x0
* Bus Check 0x20000c
* Slave Address 0xfffa0000
WARN E000

*** A system crash has occurred. (See the above messages for details.)
*** The system is now preparing to dump physical memory to disk, for use
*** in debugging the crash.

ERROR: Your system crashed before I/O and dump configuration was complete.
A crash dump cannot be taken under these circumstances without
special configuration. Contact your HP support representative.

*****

Can anyone make heads or tails of this?

Thank you all very much, your help is greatly appreciated.
 
G

Guest

Guest
Archived from groups: comp.sys.hp.hpux,comp.sys.hp.hardware (More info?)

Matthew Piechotta wrote:
> I am having a heck of a time trying to discern what is wrong with one of my
> K100s
>
> When attempting to install HP-UX, the system boots, but eventually displays
> the following on the console:
>
> ***
>
> Booting...
> Boot IO Dependent Code (IODC) revision 0
>
>
> HARD Booted.
>
> ISL Revision A.00.43 Apr12, 2000
>
> ISL booting hpux (;0):INSTALL
>
> Boot
> : disk(8/12/5.2.0.0.0.0.0;0):INSTALL
> 9707284 + 1122304 + 691712 start 0x14d568
> FLT CBFB
> ******* Unexpected HPMC. Processor HPA 0xfffa0000 *******
> GENERAL REGISTERS:
> r00/07 00000000 0010C800 00452F94 02A46800 00000089 00000000 00000000
> 02971280
> r08/15 00000001 00000002 00000003 0FD1BE2C 0014D568 FFFFFFFF 00000801
> 000331D0
> r16/23 00000001 00030720 00000008 FFB40838 00000008 00000001 00081003
> FFB40800
> r24/31 00000000 00000045 FFB40845 00A73268 00000000 00000038 7FFF0CB0
> 00081003
> CONTROL REGISTERS:
> sr0/7 00000000 00000000 00000000 00000000 00000000 0000224D 00002247
> 00000000
> pcq 00000000.0010CF84 00000000.0010CF88 isr = 00000000 ior = 00452F94
> pid1/4 0000 0000 0000 0000 ipsw = 0004000F iva = 00029800 sar = 0F ccr = C0
> tr0/7 00982AA8 00035800 FFFFFFF0 00000000 01830930 15F168E5 0009BB68
> 7FFF0BB8
> rctr = 00000000 itmr = 160B5F84 eiem = FFFFFFF0 eirr = 80000008 iir =
> E840C002
> cr1/7 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> MACHINE CHECK PARAMETERS:
> Check Type = 20000000 CPU STATE = 9E000004 Cache Check = 00000000
> TLB Check = 00000000 Bus Check = 0020000C PIM State = ? SIU Status =
> ????????
> Detected by 00000000 Assists = 00000000 Processor = 00000000
> Assist ID = 00000000 Slave Addr = FFFA0000 Master Addr = 00000000
>
>
> trap type 1 (HPMC), pcsq.pcoq = 0.10cf84, isr.ior = 0.452f94
> @(#) $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c
> 'Vw
> for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108'
> Wed N
> ov 8 19:05:38 PST 2000 $High-priority machine check: (display==0xd910,
> flags==0
> x0)
> * CPU State 0x9e000004
> * Detected By 0x0
> * Bus Check 0x20000c
> * Slave Address 0xfffa0000
> WARN E000
>
> *** A system crash has occurred. (See the above messages for details.)
> *** The system is now preparing to dump physical memory to disk, for use
> *** in debugging the crash.
>
> ERROR: Your system crashed before I/O and dump configuration was complete.
> A crash dump cannot be taken under these circumstances without
> special configuration. Contact your HP support representative.
>
> *****
>
> Can anyone make heads or tails of this?
>
> Thank you all very much, your help is greatly appreciated.
>
>
Are you trying to boot the machine with an 11i TCOE release? Try the
server version. I believe the 11i workstation release expects a PA2.0
system and the K100 is PA1.[2-3]
 
G

Guest

Guest
Archived from groups: comp.sys.hp.hpux,comp.sys.hp.hardware (More info?)

I have managed to correct the problem. I swapped out the core I/O board
from another K class system, and this solved the problem.

Now, does anyone have a core I/O board they would sell?

Please let me know.

Thanks again.
"Matthew Piechotta" <mpiechotta@shaw.ca> wrote in message
news:HR3gc.146734$Ig.136929@pd7tw2no...
> I am having a heck of a time trying to discern what is wrong with one of
my
> K100s
>
> When attempting to install HP-UX, the system boots, but eventually
displays
> the following on the console:
>
> ***
>
> Booting...
> Boot IO Dependent Code (IODC) revision 0
>
>
> HARD Booted.
>
> ISL Revision A.00.43 Apr12, 2000
>
> ISL booting hpux (;0):INSTALL
>
> Boot
> : disk(8/12/5.2.0.0.0.0.0;0):INSTALL
> 9707284 + 1122304 + 691712 start 0x14d568
> FLT CBFB
> ******* Unexpected HPMC. Processor HPA 0xfffa0000 *******
> GENERAL REGISTERS:
> r00/07 00000000 0010C800 00452F94 02A46800 00000089 00000000 00000000
> 02971280
> r08/15 00000001 00000002 00000003 0FD1BE2C 0014D568 FFFFFFFF 00000801
> 000331D0
> r16/23 00000001 00030720 00000008 FFB40838 00000008 00000001 00081003
> FFB40800
> r24/31 00000000 00000045 FFB40845 00A73268 00000000 00000038 7FFF0CB0
> 00081003
> CONTROL REGISTERS:
> sr0/7 00000000 00000000 00000000 00000000 00000000 0000224D 00002247
> 00000000
> pcq 00000000.0010CF84 00000000.0010CF88 isr = 00000000 ior = 00452F94
> pid1/4 0000 0000 0000 0000 ipsw = 0004000F iva = 00029800 sar = 0F ccr =
C0
> tr0/7 00982AA8 00035800 FFFFFFF0 00000000 01830930 15F168E5 0009BB68
> 7FFF0BB8
> rctr = 00000000 itmr = 160B5F84 eiem = FFFFFFF0 eirr = 80000008 iir =
> E840C002
> cr1/7 00000000 00000000 00000000 00000000 00000000 00000000 00000000
> MACHINE CHECK PARAMETERS:
> Check Type = 20000000 CPU STATE = 9E000004 Cache Check = 00000000
> TLB Check = 00000000 Bus Check = 0020000C PIM State = ? SIU Status =
> ????????
> Detected by 00000000 Assists = 00000000 Processor = 00000000
> Assist ID = 00000000 Slave Addr = FFFA0000 Master Addr = 00000000
>
>
> trap type 1 (HPMC), pcsq.pcoq = 0.10cf84, isr.ior = 0.452f94
> @(#) $Revision: vmunix: vw: -proj selectors:
CUPI80_BL2000_1108 -c
> 'Vw
> for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108'
> Wed N
> ov 8 19:05:38 PST 2000 $High-priority machine check: (display==0xd910,
> flags==0
> x0)
> * CPU State 0x9e000004
> * Detected By 0x0
> * Bus Check 0x20000c
> * Slave Address 0xfffa0000
> WARN E000
>
> *** A system crash has occurred. (See the above messages for details.)
> *** The system is now preparing to dump physical memory to disk, for use
> *** in debugging the crash.
>
> ERROR: Your system crashed before I/O and dump configuration was
complete.
> A crash dump cannot be taken under these circumstances without
> special configuration. Contact your HP support representative.
>
> *****
>
> Can anyone make heads or tails of this?
>
> Thank you all very much, your help is greatly appreciated.
>
>
 
G

Guest

Guest
Archived from groups: comp.sys.hp.hpux,comp.sys.hp.hardware (More info?)

Alan D Johnson wrote:

> Are you trying to boot the machine with an 11i TCOE release? Try the
> server version. I believe the 11i workstation release expects a PA2.0
> system and the K100 is PA1.[2-3]

11i TCOE works just fine with PA1.x

Benjamin
 

ASK THE COMMUNITY

TRENDING THREADS