Question New Build, No Network Connections

[Snax1224]

This is my first build and I'm running into software issues with connecting to Internet. I have no Network Adapters... I asked in another thread and was unable to find a resolution... Here are my specs, any help or farther suggestions are appreciated... Thanks!

1. AMD Ryzen 5 3600X Matisse 3>8GHz 6Core AM4 Boxed Processor with Spire Cooler
2. B450 Aorus M AMD AM4mATX Motherboard
3. Radeon RX 5600 XT Red Dragon Overclocked Dual-Fan 6GB GDDR6 PCle 4.0 Graphics Card
4. Trident Z Neo Series RGB 16GB (2 x 8GB) DDR-3600 PC4-2800 CL 16 Dual Channel Memory **Kit F-4-3600C 16D-16GTZNC-Black

5)512GB SSD 3D NAND M.2 2280 PCle NVMe 3.0 x4 Internal Solid state Drive

1. 650 Watt 80 Plus Bronze ATX Semi-Modular Power Supply
2. H510 Tempered Glass ATX Mid-Tower Computer Case- Black
3. Windows 10 ... lol

 

[popatim]

As mentioned in the other thread. make sure your built in network card is enabled inthe bios. You'll find it inthe Super IO section as Realtec PCIe GBE Family Controller Save and exit.

Back in windows, the default MS driver should automatically load and work. But you probably want to install the latest one from the support site for your board.
https://www.gigabyte.com/us/Motherboard/B450-AORUS-M-rev-10/support#support-dl

If this is your first time on that site, you probably should start with the Chipset drivers. Afterwards I install my GPU drivers (Rx5600xt for you) , and then the rest of the motherbd drivers (Sata, Lan, Audio - in that order)

https://www.amd.com/en/support/grap...d-radeon-rx-5600-series/amd-radeon-rx-5600-xt

 

[Snax1224]

As mentioned in the other thread. make sure your built in network card is enabled inthe bios. You'll find it inthe Super IO section as Realtec PCIe GBE Family Controller Save and exit.

Back in windows, the default MS driver should automatically load and work. But you probably want to install the latest one from the support site for your board.
https://www.gigabyte.com/us/Motherboard/B450-AORUS-M-rev-10/support#support-dl

If this is your first time on that site, you probably should start with the Chipset drivers. Afterwards I install my GPU drivers (Rx5600xt for you) , and then the rest of the motherbd drivers (Sata, Lan, Audio - in that order)

https://www.amd.com/en/support/grap...d-radeon-rx-5600-series/amd-radeon-rx-5600-xt

 

[Snax1224]

As mentioned in the other thread. make sure your built in network card is enabled inthe bios. You'll find it inthe Super IO section as Realtec PCIe GBE Family Controller Save and exit.

Back in windows, the default MS driver should automatically load and work. But you probably want to install the latest one from the support site for your board.
https://www.gigabyte.com/us/Motherboard/B450-AORUS-M-rev-10/support#support-dl

If this is your first time on that site, you probably should start with the Chipset drivers. Afterwards I install my GPU drivers (Rx5600xt for you) , and then the rest of the motherbd drivers (Sata, Lan, Audio - in that order)

https://www.amd.com/en/support/grap...d-radeon-rx-5600-series/amd-radeon-rx-5600-xt

There was a disk with those drivers that came with the motherboard which I transfered to a USB and installed onto the computer.

as far as the Super IO section (located in peripherals!?) it only has serial Port 1- Enabled and Parallel Port-Enabled

At this point I'm willing to pay someone to facetime and walk me through it, long as they can help me fix it... $100! Lol

 

[popatim]

Enable that controller. That's the builtin network card. Click on it and it should show you the options [enable or disable] then click enable.

It should also enable if you reset the bios to defaults but you will loose any changes that you made it in and have to redo them.

 

[Snax1224]

Enable that controller. That's the builtin network card. Click on it and it should show you the options [enable or disable] then click enable.

It should also enable if you reset the bios to defaults but you will loose any changes that you made it in and have to redo them.

Thanks for responding Popatim, but there was no "RealTek PCi" controller that I saw. And the both ports are already Enabled. Also I could reset the Bios at any point and it would be fine with me because I've never done anything or made any changes in Bios since its been built. Should I have done something upon construction? Thanks again man. You're continued support is appreciated!