Hello,
I am having major downfalls with my new PC Build.
What we have is:
ThermalTake A500 case
Asus Z490 TUF Gaming Plus
Intel I9 10850k
G Skill Trident Z 32gb (F4-2933C14D-32GTZRX)
Corsair H150i Elite Capellix cooler
XFX PRO850w XXX edition semi modular PSU
No GPU, Only using onboard, I have HDMI and DP to the same monitor with auto detect on monitor, monitor was working on previous gen4 build via DP, also my PS3 proved the HDMI is functional.
I boot, there's no video signal, There's no ability to CAPS NUM or SCROLL toggle via keyboard.
The Q-LEDs light in this order then disappear.
CPU>DRAM>OFF
No boot device in installed, yet no BOOT Q-LED will light. No VGA is installed, yet no signal is output via onboard HDMI or DP.
I have my Capellix cooler plugged in with the pump in CPU_FAN and a usb header to commander core. Without the USB header plugged in the fans spin on full due to CPU pump not being turned on.
Chassis Fans act normal, RAM and cooler RGB are functional, if I remove RAM the mobo speaker works fine.
All parts are brand new besides PSU. The PSU doesn't have an 8+4 eatx_v12 cable but It does have 4+4 eatx_v12 which I always plug in.
I tried previously with boot devices installed and had no joy with signal then tried without to be sure the boot led was functional.
CTRL-ALT-DEL doesn't restart the pc once the keyboard is backlit, but the rest button works no problem.
I tried F1 first then CTRL-ALT-DEL too to be sure I bypassed any reset bios prompts which may or may not have appeared.
I tried installing my old artifacted 1080ti to see if the mobo (just) required a VGA installed for first boot, then 5-6 second shutdown, uninstalled the 1080 plugged the HDMI back into the onboard and still no post display or caps lock toggle abilities were unlocked.
I've reseat RAM and CPU 2-3 times, also the rear port shielding has been Reseated/exchanged.
*This is actually my second TUF Z490 mobo, my first was DOA as it only had aura lighting but no reaction to being powered on, either via case switch or power pin contact inside. That mobo didn't even try. This one I think I've tried all cheat codes for now, including resetting the CMOS via power drain>battery pull>clctr pins contacted for 5-10 seconds>power up, and switch on. The BIOS did reset, each time it was told to, but no video output at any point even after allowing to boot then spam reset switch. Again all QLEDs sequenced during boot except for BOOT LED which seems odd.
850 watts is enough for the setup, but I'm now inclined to rebuild my 4th gen and double check that 'it' still boots determining my PSU not at fault. I feel it's actually the mobo, or CPU being the killer culprit. What do you think?
I am having major downfalls with my new PC Build.
What we have is:
ThermalTake A500 case
Asus Z490 TUF Gaming Plus
Intel I9 10850k
G Skill Trident Z 32gb (F4-2933C14D-32GTZRX)
Corsair H150i Elite Capellix cooler
XFX PRO850w XXX edition semi modular PSU
No GPU, Only using onboard, I have HDMI and DP to the same monitor with auto detect on monitor, monitor was working on previous gen4 build via DP, also my PS3 proved the HDMI is functional.
I boot, there's no video signal, There's no ability to CAPS NUM or SCROLL toggle via keyboard.
The Q-LEDs light in this order then disappear.
CPU>DRAM>OFF
No boot device in installed, yet no BOOT Q-LED will light. No VGA is installed, yet no signal is output via onboard HDMI or DP.
I have my Capellix cooler plugged in with the pump in CPU_FAN and a usb header to commander core. Without the USB header plugged in the fans spin on full due to CPU pump not being turned on.
Chassis Fans act normal, RAM and cooler RGB are functional, if I remove RAM the mobo speaker works fine.
All parts are brand new besides PSU. The PSU doesn't have an 8+4 eatx_v12 cable but It does have 4+4 eatx_v12 which I always plug in.
I tried previously with boot devices installed and had no joy with signal then tried without to be sure the boot led was functional.
CTRL-ALT-DEL doesn't restart the pc once the keyboard is backlit, but the rest button works no problem.
I tried F1 first then CTRL-ALT-DEL too to be sure I bypassed any reset bios prompts which may or may not have appeared.
I tried installing my old artifacted 1080ti to see if the mobo (just) required a VGA installed for first boot, then 5-6 second shutdown, uninstalled the 1080 plugged the HDMI back into the onboard and still no post display or caps lock toggle abilities were unlocked.
I've reseat RAM and CPU 2-3 times, also the rear port shielding has been Reseated/exchanged.
*This is actually my second TUF Z490 mobo, my first was DOA as it only had aura lighting but no reaction to being powered on, either via case switch or power pin contact inside. That mobo didn't even try. This one I think I've tried all cheat codes for now, including resetting the CMOS via power drain>battery pull>clctr pins contacted for 5-10 seconds>power up, and switch on. The BIOS did reset, each time it was told to, but no video output at any point even after allowing to boot then spam reset switch. Again all QLEDs sequenced during boot except for BOOT LED which seems odd.
850 watts is enough for the setup, but I'm now inclined to rebuild my 4th gen and double check that 'it' still boots determining my PSU not at fault. I feel it's actually the mobo, or CPU being the killer culprit. What do you think?