Over clock PD 920 help!

[danbooky]

I am putting up a new rig right now aiming to the max I can get with these set up. So please help. Any one with the same or semiliar set up please share your experience.
Any help will be appreciated.
Asus P5LD2$142
CPU PD 920 $179
500W Thermaltake $20
PNY GEForce 7600gs $149
OCZ PC2 6400 1gb EL Dual CH Platium Edition XTC 4-5-4-15 $150
Zalman CNPS9500 Led $64.99 Or Thermaltake Big water SE $109
All the hardwares are ready and being put together rightnow. I'll be checking the replys as i'am working on it.
Thanks, Dan

 

[kwalker]

you should get well over 3.7 ghz . but no two boards clock the same.
make sure you have asus latest bios (not the betas)
first thing ...dont rush to max your oc.
use the pre set auto features at first to slowly get up to 20% oc.
prime 95 for at least 6 hours monitoring temps. the 920 is a cool runner.
after all is stable use the maunual mode to bring up the fsb.
you shouldnt need voltage adjustments to stabilize up to 3.4 and over.
I personally never had the vcore past 1.375 @ 3.87ghz.
my sweet spot is in my sig.
I ve hit over 4 on air but who needs 4ghz ? and that takes serious cooling to run 24/7
keep us posted.

 

[danbooky]

It is Dan
Just had it finished. I was looking for the PLL for KeyGen then found out the MB had one big circuit line scratched off completely from the board. So i'am on the way to Fry's for exchanging. Darn it
I'll be back

 

[kwalker]

make sure the bios is supporting 65nm (red sticker on box)

 

[danbooky]

I am putting up a new rig right now aiming to the max I can get with these set up. So please help. Any one with the same or semiliar set up please share your experience.
Any help will be appreciated.
Asus P5LD2$142
CPU PD 920 $179
500W Thermaltake $20
PNY GEForce 7600gs $149
OCZ PC2 6400 1gb EL Dual CH Platium Edition XTC 4-5-4-15 $150
Zalman CNPS9500 Led $64.99 Or Thermaltake Big water SE $109
All the hardwares are ready and being put together rightnow. I'll be checking the replys as i'am working on it.
Thanks, Dan

Got it stable at 4.0014gz (fsb at 286, Vcore at 1.350v, memory at 1.9v, pcie at 1.6v) now. Test with prime95 for 12hours :lol:
One question about the heat tolerance of the PRESLEY: how much?
mine is at (47 to 62). Is it too hot?
Possible to push it at 4.3 with water cool.

 

[ak47is1337]

I am putting up a new rig right now aiming to the max I can get with these set up. So please help. Any one with the same or semiliar set up please share your experience.
Any help will be appreciated.
Asus P5LD2$142
CPU PD 920 $179
500W Thermaltake $20
PNY GEForce 7600gs $149
OCZ PC2 6400 1gb EL Dual CH Platium Edition XTC 4-5-4-15 $150
Zalman CNPS9500 Led $64.99 Or Thermaltake Big water SE $109
All the hardwares are ready and being put together rightnow. I'll be checking the replys as i'am working on it.
Thanks, Dan

Got it stable at 4.0014gz (fsb at 286, Vcore at 1.350v, memory at 1.9v, pcie at 1.6v) now. Test with prime95 for 12hours :lol:
One question about the heat tolerance of the PRESLEY: how much?
mine is at (47 to 62). Is it too hot?
Possible to push it at 4.3 with water cool.
You should hit 4.7 with water cooling ez. Also, Intel chips have very high heat tolerances, especially NetBurst chips. Your temps are pretty good as is.

 

[danbooky]

Update with water cool BIG WATER SE here is the result
Bios boot at 4.2gz at 299 fsb but window run for 1 minute and shut down for preventing damage to harewares But the CPU temp rage was at only 47-65. huh
Is there any way to disable this safety feature from windowxppro??
Thanks :lol:

 

[kwalker]

up the termination voltage in bios but dont let the temps smoke that cpu.
disable thermal protection in bios to see if it stailizes.
I would drop the front side bus down a little.
if you got the bsod mabie the ram needs tightening

 

[kwalker]

brain fart 😳
forgot to ask what reporting software your using.
there are adjustments within the software.to raise and lower thermal points