Question Question about drive health output

[Austin2442]

Hello, I am in the process of setting up a home server and just for the heck of it I ran my newly purchased seagate 18tb harddrive throught a SMART test to see how its reading. This drive was bought in June but hasnt been used at all until yesterday so it should be fine. The output from the test is worring me but since im not an expert I was wondering if anyone can tell me if I should be worried and replace the drive. Thanks for the help ill paste the output below.

Output from running sudo smartctl -a /dev/sda1

=== START OF INFORMATION SECTION ===
Device Model: ST18000NM000J-2TV103
Serial Number: ZR57ZEM5
LU WWN Device Id: 5 000c50 0e3e56bac
Firmware Version: SN02
User Capacity: 18,000,207,937,536 bytes [18.0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database 7.3/5319
ATA Version is: ACS-4 (minor revision not indicated)
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Wed Jul 27 19:14:42 2022 EDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 575) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: (1562) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x70bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 081 064 044 Pre-fail Always - 127227494
3 Spin_Up_Time 0x0003 091 091 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 9
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 061 060 045 Pre-fail Always - 1272890
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 10
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 9
18 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 071 067 000 Old_age Always - 29 (Min/Max 23/29)
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 5
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 12
194 Temperature_Celsius 0x0022 029 040 000 Old_age Always - 29 (0 23 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0023 100 100 001 Pre-fail Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 10 (70 65 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 4521369120
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 4295500270

SMART Error Log Version: 1
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

****

 

[USAFRet]

Assuming a Windows OS, run CrystalDiskInfo, and post a screencap of that window here.
MUCH easier than trying to read through that text.

(upload your pic to imgur.com, post the link here)

 

[Austin2442]

Assuming a Windows OS, run CrystalDiskInfo, and post a screencap of that window here.
MUCH easier than trying to read through that text.

(upload your pic to imgur.com, post the link here)

Im on Linux so I found a similar GUI too to CrystalDiskInfo and it says that the disk is fine. I might also check it on CrystalDiskInfo later. Thanks for the help have a good rest of your day.

 

[fzabkar]

If you are concerned about the Raw Read Error Rate and Seek Error Rate attributes, these are not error counts. Instead they are sector counts and seek counts. In fact the actual number of seek errors is 0.