- Apr 14, 2002
- 20,603
- 6
- 52,915
I just finished installing RAM Heatsinks,(IE;Ramsinks) on my ATI 9800 Pro, I applied an old carpenters trick, to the RAM sink installation and it worked great, so I thought I'd pass it on.
I used the Artic Silver Thermal Adhesive, which as we all should know, conducts electricity, and you cannot take any chance whatsoever of getting the ASTA on any electrical surfaces.
So first I carefully scotch taped around each RAM die, now for the tip, I used a sheet of plastic like the plastic that transperencies are made of to mix the ASTA together on, the plastic needs to be thick enough not to be moving when you hold it to spread the Thermal Adhesive on, after I had the adhesive thoroughly mixed, I spread a thin even layer out on the plastic sheet, then pressed the contact base of the Ramsink into the thin layer of adhesive, twisting it back and forth and checking for even coverage, if I had too much on it, I went to a thinner spread on the plastic and evened it up, then used the contact part of the ram sink, and touched the die with the contact face of the Ramsink, pulling it up and checking for even coverage on the die, and basically using the base of the Ramsink to spread the Thermal adhesive, since it was the exact same size as the die it was the perfect spreader.
Doing it that way there was a very slight squeeze out when pressure was applied to the Ramsinks, for the setup time period, that allows the Thermal Adhesive to cure.
Spreading the Thermal Adhesive on the plastic basically gives you the perfect coverage thickness to begin with and with a steady hand, removes the possibility of getting the Thermal Adhesive where you don't want it. It worked great, and I had no problems at all.
I hope this tip helps someone, with your own Ramsink installation!
Anyone thats installed Ramsinks on a video card using Artic Silver Thermal Adhesive knows just how nerve racking it can be, because you surely don't want to screw up your video card.
Ryan
<A HREF="http://forums.btvillarin.com/index.php?act=ST&f=41&t=2541" target="_new">My Rig</A>
I used the Artic Silver Thermal Adhesive, which as we all should know, conducts electricity, and you cannot take any chance whatsoever of getting the ASTA on any electrical surfaces.
So first I carefully scotch taped around each RAM die, now for the tip, I used a sheet of plastic like the plastic that transperencies are made of to mix the ASTA together on, the plastic needs to be thick enough not to be moving when you hold it to spread the Thermal Adhesive on, after I had the adhesive thoroughly mixed, I spread a thin even layer out on the plastic sheet, then pressed the contact base of the Ramsink into the thin layer of adhesive, twisting it back and forth and checking for even coverage, if I had too much on it, I went to a thinner spread on the plastic and evened it up, then used the contact part of the ram sink, and touched the die with the contact face of the Ramsink, pulling it up and checking for even coverage on the die, and basically using the base of the Ramsink to spread the Thermal adhesive, since it was the exact same size as the die it was the perfect spreader.
Doing it that way there was a very slight squeeze out when pressure was applied to the Ramsinks, for the setup time period, that allows the Thermal Adhesive to cure.
Spreading the Thermal Adhesive on the plastic basically gives you the perfect coverage thickness to begin with and with a steady hand, removes the possibility of getting the Thermal Adhesive where you don't want it. It worked great, and I had no problems at all.
I hope this tip helps someone, with your own Ramsink installation!
Anyone thats installed Ramsinks on a video card using Artic Silver Thermal Adhesive knows just how nerve racking it can be, because you surely don't want to screw up your video card.
Ryan <A HREF="http://forums.btvillarin.com/index.php?act=ST&f=41&t=2541" target="_new">My Rig</A>
: why do we need money when we can just stay in our room and have sex all day?
Facebook
Twitter
Instagram