Recent content by ajay12131

Hello again @kerberos_20. Running MemTest found errors and I started from the very beginning as you suggested, tRFC = 630 and the system was quite stable there. So I tweaked certain values and now the system is running at tRFC = 612. MemTest86 found ZERO errors in all tests for 2 complete...

Greetings @kerberos_20. I'll run memtest and post the outcome here. Thanks for your guidance. Much appreciated.

Thanks @kerberos_20 for the helpful reply. As you said, the UEFI was displaying incorrect tRFC information at AUTO. And as per your suggestion, I first set it to 550 and it worked. So I tried lowering it further down to 545 as you mentioned and it still worked. Not to mention I also applied the...

Hello everyone. I recently upgraded my RAM to 2 x 16GB @3000mhz (mismatched sticks) and managed to run them in dual-channel @3600mhz. There is no stability issue yet (over 1 month of usage). However, I recently noticed something called tRFC 990 (I am a newbi to oc) in HWINFO summary. I looked...

Hello @Darkbreeze. I have finally found the best working configuration for my RAMs with clearly noticeable performance gain in everything including gaming. There is a clearly visible smoothness in overall system performance. Even though the latency is even higher than 3200mhz, still I can...

Thank you @Darkbreeze. I will compare Realbench, Cinebench R23 and 3dmark scores on both configurations 5 times each and will finally make my decision on which configuration to use based on the average results of all 3 tools. Thanks again for giving you time and advice. Regards.

I did as you suggested and reset the complete BIOS to its default and now Its running at default DOCP profile and nothing else is touched in the OC section. Everything is set to its default. But the DRAM timings are still locked. The result is same 3000mhz @ 16-20-20-38-70 and I still can't...

Greetings @Darkbreeze. Actually it took 1 hour 20 minutes to complete one pass so I didn't tried to go further as I have too many random power outages in my area. But I will try to run the tests overnight counting on my luck to see what comes out. By the way, I didn't touched anything in the...

I ran the Memtest86 as you suggested and no errors were detected. I tried all of the 13 tests for 1 complete pass with both, XMP @3000mhz and manual oc @3200mhz without any issue detected. I also tried gaming and video rendering of the same project to test any improvement in timing...

So I switched DOCP (XMP) on in BIOS and tried CPU-Z validation again and got these results now: CPU-Z 2.03 CPU-Z 1.99 The timings are now 16-20-20-38-70 but still not 16-20-20-38-58. Should I still tweak the latency manually?

No, not XMP, but I have manually set the RAM Frequency to 3200mhz, as I was running my single RAM stick at 3200mhz. Actually I didn't even touched in the BIOS after installing the new RAM stick. Just checked in the task manager and it displayed 3200mhz. And then in CPU-Z. That is all. Since both...

Thank you @Darkbreeze. By the way I cannot notice any performance difference in my gaming or video rendering performance. Though it was NOT the main purpose of upgrading to 32GB RAM, still curious if the dual-channel benefits are noticeable or not.

Greetings @Darkbreeze. So I finally took my chances and bought a new CMK16GX4M1D3000C16 - VENGEANCE® LPX and paired it with my existing CMW16GX4M1D3000C16 - VENGEANCE® RGB PRO. Good for me that they are running in dual-channel configuration as far as I can understand. The latest version of CPU-Z...

Thank you so much for that quick reply. The link is very helpful as well. Going through it, I suppose I'd rather buy a single kit of dual-channel certified RAM as you mentioned above. Thanks again with regards.

So I have a CORSAIR VENGEANCE® RGB PRO 16GB (1 x 16GB) DDR4 DRAM 3000MHz C16, model number CMW16GX4M1D3000C16 ( https://bit.ly/3UWNWzv ) RAM paired with a Ryzen 5 3600 processor on a B450M motherboard. I was just planning to upgrade my RAM to 32GB (2 x 16GB), but the identical model is not...