Archived from groups: alt.comp.periphs.mainboard.soyo (
More info?)
"Knuckles" <knuckles6@sbcglobal.net> wrote in message news:<Xu5Yc.8201$FV3.4159@newssvr17.news.prodigy.com>...
> Vince,
>
> Your Celeron 2.7 is a discontinued model thats why I didn't think there was
> one. The Radeon 9200 is a compatable card, the video card must be AGP4X to
> be used on this board and your Radeon 9200 is rated 2X,4X, and 8X so thats
> not a problem.
>
> Your not going to hear beep codes unless you have a case speaker connected
> to the motherboard. Headphones won't work because they require the onboard
> sound to work and it doesn't till after you get the operating system loaded
> and the sound drivers loaded. I don't know what case your using but most
> have a speaker built into the front of the case with a flat four pin
> connector that would be plugged in to the motherboard in the lower right
> corner of the motherboard, in the group of pins where you connect the power
> switch and hard drive light to the motherboard. This speaker works for the
> beep codes, thats about all it does. With a speaker connected here you would
> get a beep at post and a series of beeps if there was a memory problem or
> video problem. You would get no beep code if the cpu was bad, in fact you
> would get just about what you are getting if the cpu was bad.
>
> If you have a near by computer shop you could take the cpu in and see if
> they will test it for you. Most will for a couple of bucks. Since your
> getting power to the cpu fan when you hit the power switch that would be my
> first suggestion, have the cpu tested. You could also have your video card
> and memory checked. If there all are fine then all thats left to look at
> would be your motherboard.
>
> "Vince" <dragon_slash2@hotmail.com> wrote in message
> news:6e76f458.0408280819.22a779eb@posting.google.com...
> > j.burghdoff@sbcglobal.net (Jim B.) wrote in message
> > news:<a182f0ed.0408271523.5bc52e18@posting.google.com>...
> >> dragon_slash2@hotmail.com (Vince) wrote in message
> >> news:<6e76f458.0408270947.e88c266@posting.google.com>...
> >>
> >> First problem with your post is there is no SY-P4I 845P5, so it must
> >> be the SY-P4I PE or the SY-P4I 845PE V.1 or the SY-P4IPE ISA? To find
> >> out look on the motherboard between the PCI slots and it will be
> >> printed on the board in white.
> >>
> >> Next you say you have a Celeron 2.7 but there isn't a 2.7 Celeron or
> >> CeleronD. You say you have a 350w powersupply but is it an ATX power
> >> supply or ATX12V power supply. The P-4 based boards require the ATX12V
> >> power supply. The difference is that it has two connections for the
> >> motherboard, it has the standard 20pin connector the ATX power supply
> >> has and an additional square 4 pin power connector.
> >>
> >> When you turn on the power you hear no beep, do you have the case
> >> speaker wires connected to the right spot? Your getting some power to
> >> the board if the cpu fan is running. So fisrt make sure that speaker
> >> connection is correct. Second make sure your square four pin power
> >> cable is connected to the motherboard.
> >>
> >> Next make sure your agp card is a 1.5 volt card, older ones were 3.3
> >> so if your using an old video card it could be a problem. Also make
> >> sure the card is firmly seated in its slot. They go in very hard
> >> usually makes two pops as it locks in.
> >> > i bought a new MB ( Sy-p4i 845p5) and a new cpu(celeron 2.7)
> >> >
> >> > the problem is that when i turn on my comp the powersuply and cpu fan
> >> > are running but i hear no beep sound and i see nothing on monitor...
> >> >
> >> > the powersuply is 350w and its enought
> >> > i tryed starting the MB wiht the strick minimun and outside the case..
> >> > i tryed clearing cmos
> >> >
> >> > and its still the same...is the MB fryed? or its the cpu?
> >> >
> >> > plz help guys
> >> >
> >> > V!nce
> >
> > hrm my motherboard is a SY-P4I 845PE V.1 and my cpu is clearly a
> > celeron 2.7ghz(thats whats its says on the package)my power suply is
> > got the 4 pin thing(it came whit my bro p4)and my videocard is a
> > radeon 9200 but i dont know the volts
> > and for the beep thing..i dont have speakers but does earphone works?
> >
> > thx
> > V!nce
hmmm..well,the speaker of the case was pluged all along.im gonna try
an another cpu on my MB to see if its the cpu or the motherboard is
fryed..i hope its gonna work
😛
thx for the info(man,you rock)
V!nce
Facebook
Twitter
Instagram