Intel I219-V refuses to establish a connection! always disconnected !

Status
Not open for further replies.

mhamdy

Honorable
Oct 18, 2013
8
0
10,520
My problem is quite simple, yet I can not find a solution for!
When I plug my cable into the Ethernet port in my new PC, I can not get a connection established to the router! That's it.
.
Please note the following:
1. I219-V driver version 12 (latest, I also tried the one with my MoBo, no luck)
11.png


2. Intel PROset version 22.6 (latest)
10.png


3. My computer successfully recognizes and installs the Ethernet driver (the card is not dead :D)
8.png


4. The network cable is working perfectly ( I havel also used different cables)
7.png


5. Using the diagnostics in Intel PROSet, the on-board card actually responds when I start the "Led Blinking" (it is not dead)
4.png


6.Using the diagnostics in Intel PROSet, it fail when I test a connection
5.png


7. The router (linksys 1900 ACS) is working perfectly (WAN and all LAN ports) - DHCP is enabled and working perfectly.
9.png


8. It only works rarely when I set the negotiation mode to 10 Mbps full duplex
1.png


9. When I set it to "Auto" or "1 Gbps full duplex" I still get disconnected.
2.png


So, in short, I am sure everything in the system working properly ( as I used different routers. cables, laptops, etc) except for this cursed network adapter, so any ideas ?? :D :ange:

-------------------------
System Information
------------------
Operating System: Windows 10 Pro 64-bit (10.0, Build 15063) (15063.rs2_release.170317-1834)
MoBo: Asus Maximus IX Hero z270 chipset
BIOS: 0701
Processor: Intel(R) Core(TM) i7-7700K CPU @ 4.20GHz (8 CPUs), ~4.2GHz
Memory: 16384MB RAM
Card name: NVIDIA GeForce GTX 1080
Dedicated Memory: 8110 MB
Description: Realtek Digital Output (Realtek High Definition Audio)
Name: Intel(R) 200 Series Chipset Family PCI Express Root Port #9 - A298
Name: Intel(R) Ethernet Connection I219-V



 
Solution
Problem solved.


I tried to restore the firmware to defaults using "EEPROM using Intel® Ethernet Connections Boot Utility, Preboot Images, and EFI Drivers" using the following command:

BOOTUTILW64E.exe -NIC=1 -DEFAULTCONFIG
12.png


Now I got the 1 Gbps STABLE connection.

mhamdy

Honorable
Oct 18, 2013
8
0
10,520
Problem solved.


I tried to restore the firmware to defaults using "EEPROM using Intel® Ethernet Connections Boot Utility, Preboot Images, and EFI Drivers" using the following command:

BOOTUTILW64E.exe -NIC=1 -DEFAULTCONFIG
12.png


Now I got the 1 Gbps STABLE connection.
 
Solution

pebbleslabrador

Prominent
Jan 26, 2018
3
0
510


 
Mar 30, 2018
1
0
10
Hello all,

I have Asus Strix z270H with the intel networking card in Windows 10 Pro.

Seems like the Open WRT router I have in my system does not know how to give IP6 address to the PC and the driver for the NIC refuses to connect most of the time.

My solution was to disable the Internet Protocol Version 6 (TCP/IPv6) in the Ethernet Connection's properties.

Since disabling the IPv6 the connection has established immediately after wake up from sleep or from boot up.

Hope this helps some of you.
 
Status
Not open for further replies.