NF&-S Ver 2. and Windows XP

Toggle sidebar Toggle sidebar
M

ME

Distinguished
Apr 1, 2004
1,746
0
19,780
Archived from groups: alt.comp.periphs.mainboard.abit (More info?)

To all Wizards

Main Issue: nForce2 SPP chipset drivers not recognized by Windows XP
Home Edition

Following is my system configuration:

NF7-S V2 motherboard
Athlon XP 2800 processor, 333 front bus, not overclocked
Bios number 23 (have used 20 and 21 with same results)
Current nForce driver version 3.13, have used nforce driver that came
with mb disk, same results
Windows XP Home Edition, all updates installed. Windows was installed
from a clean setup.
ATA serial raid version 4.2.47, set up as a raid 0
Hard drives, Seagate Barracuda 7200 80 gig.
Memory, two Siemens 512 Meg DDR-SDRAM PC-3200, running at 400 MHZ. Have
tried 333 MHZ, and other ram sticks with same result.
Memory modules set up in slots 2 and 3, upon boot "Dual DDR" message
displayed.
Radeon 9600XT AGP video card, latest drivers.
On board audio and LAN enabled, IEEE disabled.

Problem:

My Computer - System - Hardware - Device Manager- System Devices

Basic display for computer hardware shows no conflicts, disabled
devices, or other Windows warning icons.

The following listed items have "No Drivers installed for this device"
displayed when they are first selected in the "General" display box for each
device:
When I advance to the "Drivers Tab" display box, Windows lists nVida
drivers as being installed. All driver versions dates are 4/9/2003.

nVidia nForce2 PCI System Management
nVidia nForce2 Memory Controller (4 of these are listed)
nVidia nForce 2 Ultra 400 Memory Controller

When clicking on all other nForce devices, such as AGP devices, Windows
"General" display box says that drivers have been installed.

Troubleshooting efforts to date:

Two Clean installs of Windows. All Windows updates are installed. Have
tried three different BIOS versions. Have tried two different nForce
unified driver versions. I have uninstalled the nForce drivers via the
Control Panel Remove Programs tab before installing new unified drivers. I
have uninstalled each of the above items utilizing the Device manager, then
rebooted the computer and let the system find the new device and let Windows
install the driver. I have used the option in the BIOS of "Force Update
ESCD".

Any suggestions on this problem are greatly appreciated. Thanks in
advance

Dave
 
Archived from groups: alt.comp.periphs.mainboard.abit (More info?)

me wrote:
> To all Wizards
>
> Main Issue: nForce2 SPP chipset drivers not recognized by Windows
> XP Home Edition
>
> Following is my system configuration:
>
> NF7-S V2 motherboard
> Athlon XP 2800 processor, 333 front bus, not overclocked
> Bios number 23 (have used 20 and 21 with same results)
> Current nForce driver version 3.13, have used nforce driver that
> came with mb disk, same results
> Windows XP Home Edition, all updates installed. Windows was
> installed from a clean setup.
> ATA serial raid version 4.2.47, set up as a raid 0
> Hard drives, Seagate Barracuda 7200 80 gig.
> Memory, two Siemens 512 Meg DDR-SDRAM PC-3200, running at 400
> MHZ. Have tried 333 MHZ, and other ram sticks with same
> result. Memory modules set up in slots 2 and 3, upon boot "Dual
> DDR" message displayed.
> Radeon 9600XT AGP video card, latest drivers.
> On board audio and LAN enabled, IEEE disabled.
>
> Problem:
>
> My Computer - System - Hardware - Device Manager- System Devices
>
> Basic display for computer hardware shows no conflicts, disabled
> devices, or other Windows warning icons.
>
> The following listed items have "No Drivers installed for this
> device" displayed when they are first selected in the "General"
> display box for each device:
> When I advance to the "Drivers Tab" display box, Windows lists
> nVida drivers as being installed. All driver versions dates are
> 4/9/2003.
>
> nVidia nForce2 PCI System Management
> nVidia nForce2 Memory Controller (4 of these are listed)
> nVidia nForce 2 Ultra 400 Memory Controller
>
> When clicking on all other nForce devices, such as AGP devices,
> Windows "General" display box says that drivers have been installed.
>
> Troubleshooting efforts to date:
>
> Two Clean installs of Windows. All Windows updates are
> installed. Have tried three different BIOS versions. Have tried two
> different nForce unified driver versions. I have uninstalled the
> nForce drivers via the Control Panel Remove Programs tab before
> installing new unified drivers. I have uninstalled each of the above
> items utilizing the Device manager, then rebooted the computer and
> let the system find the new device and let Windows install the
> driver. I have used the option in the BIOS of "Force Update ESCD".
>
> Any suggestions on this problem are greatly appreciated. Thanks
> in advance
>
> Dave

That's normal. Same on my XP Home system (NF7-S ver. 2.0). If you look
at the Driver tab, it shows Driver Provider: NVIDIA, date and version,
but Driver Details says "no driver files required or loaded for this
device", emphasis on "not required". As long as the devices are
correctly identified, it appears that's all that is needed.
 
Archived from groups: alt.comp.periphs.mainboard.abit (More info?)

That's normal, same thing here on XP Pro.

--
*****Replace 'NOSPAM' with 'btinternet' in the reply address*****
"me" <davebarbs@sio.midco.net> wrote in message
news:1082kdu8kr3v1e9@corp.supernews.com...
> To all Wizards
>
> Main Issue: nForce2 SPP chipset drivers not recognized by Windows XP
> Home Edition
>
> Following is my system configuration:
>
> NF7-S V2 motherboard
> Athlon XP 2800 processor, 333 front bus, not overclocked
> Bios number 23 (have used 20 and 21 with same results)
> Current nForce driver version 3.13, have used nforce driver that came
> with mb disk, same results
> Windows XP Home Edition, all updates installed. Windows was installed
> from a clean setup.
> ATA serial raid version 4.2.47, set up as a raid 0
> Hard drives, Seagate Barracuda 7200 80 gig.
> Memory, two Siemens 512 Meg DDR-SDRAM PC-3200, running at 400 MHZ.
Have
> tried 333 MHZ, and other ram sticks with same result.
> Memory modules set up in slots 2 and 3, upon boot "Dual DDR" message
> displayed.
> Radeon 9600XT AGP video card, latest drivers.
> On board audio and LAN enabled, IEEE disabled.
>
> Problem:
>
> My Computer - System - Hardware - Device Manager- System Devices
>
> Basic display for computer hardware shows no conflicts, disabled
> devices, or other Windows warning icons.
>
> The following listed items have "No Drivers installed for this device"
> displayed when they are first selected in the "General" display box for
each
> device:
> When I advance to the "Drivers Tab" display box, Windows lists nVida
> drivers as being installed. All driver versions dates are 4/9/2003.
>
> nVidia nForce2 PCI System Management
> nVidia nForce2 Memory Controller (4 of these are listed)
> nVidia nForce 2 Ultra 400 Memory Controller
>
> When clicking on all other nForce devices, such as AGP devices, Windows
> "General" display box says that drivers have been installed.
>
> Troubleshooting efforts to date:
>
> Two Clean installs of Windows. All Windows updates are installed.
Have
> tried three different BIOS versions. Have tried two different nForce
> unified driver versions. I have uninstalled the nForce drivers via the
> Control Panel Remove Programs tab before installing new unified drivers.
I
> have uninstalled each of the above items utilizing the Device manager,
then
> rebooted the computer and let the system find the new device and let
Windows
> install the driver. I have used the option in the BIOS of "Force Update
> ESCD".
>
> Any suggestions on this problem are greatly appreciated. Thanks in
> advance
>
> Dave
>
>
 
Archived from groups: alt.comp.periphs.mainboard.abit (More info?)

"BigBadger" <big_badger@NOSPAM.com> wrote in message
news:c5t9u6$t5d$1@news7.svr.pol.co.uk...
> That's normal, same thing here on XP Pro.
>
> --
> *****Replace 'NOSPAM' with 'btinternet' in the reply address*****
> "me" <davebarbs@sio.midco.net> wrote in message
> news:1082kdu8kr3v1e9@corp.supernews.com...
> > To all Wizards
> >
> > Main Issue: nForce2 SPP chipset drivers not recognized by Windows XP
> > Home Edition
> >
> > Following is my system configuration:
> >
> > NF7-S V2 motherboard
> > Athlon XP 2800 processor, 333 front bus, not overclocked
> > Bios number 23 (have used 20 and 21 with same results)
> > Current nForce driver version 3.13, have used nforce driver that
came
> > with mb disk, same results
> > Windows XP Home Edition, all updates installed. Windows was
installed
> > from a clean setup.
> > ATA serial raid version 4.2.47, set up as a raid 0
> > Hard drives, Seagate Barracuda 7200 80 gig.
> > Memory, two Siemens 512 Meg DDR-SDRAM PC-3200, running at 400 MHZ.
> Have
> > tried 333 MHZ, and other ram sticks with same result.
> > Memory modules set up in slots 2 and 3, upon boot "Dual DDR" message
> > displayed.
> > Radeon 9600XT AGP video card, latest drivers.
> > On board audio and LAN enabled, IEEE disabled.
> >
> > Problem:
> >
> > My Computer - System - Hardware - Device Manager- System Devices
> >
> > Basic display for computer hardware shows no conflicts, disabled
> > devices, or other Windows warning icons.
> >
> > The following listed items have "No Drivers installed for this
device"
> > displayed when they are first selected in the "General" display box for
> each
> > device:
> > When I advance to the "Drivers Tab" display box, Windows lists nVida
> > drivers as being installed. All driver versions dates are 4/9/2003.
> >
> > nVidia nForce2 PCI System Management
> > nVidia nForce2 Memory Controller (4 of these are listed)
> > nVidia nForce 2 Ultra 400 Memory Controller
> >
> > When clicking on all other nForce devices, such as AGP devices, Windows
> > "General" display box says that drivers have been installed.
> >
> > Troubleshooting efforts to date:
> >
> > Two Clean installs of Windows. All Windows updates are installed.
> Have
> > tried three different BIOS versions. Have tried two different nForce
> > unified driver versions. I have uninstalled the nForce drivers via the
> > Control Panel Remove Programs tab before installing new unified drivers.
> I
> > have uninstalled each of the above items utilizing the Device manager,
> then
> > rebooted the computer and let the system find the new device and let
> Windows
> > install the driver. I have used the option in the BIOS of "Force Update
> > ESCD".
> >
> > Any suggestions on this problem are greatly appreciated. Thanks in
> > advance
> >
> > Dave
> >
> >
>
>

I have XP Pro and an NF7-S ver. 2 and it shows five nVidia nForce2 Memory
Controllers but none of them say nVidia nForce 2 Ultra 400 Memory
Controller. Wonder why the Utra controller is not listed on mine?
 
Archived from groups: alt.comp.periphs.mainboard.abit (More info?)

Mine says Ultra 400 just like the original poster...Are you running your
memory dual channel?

--
*****Replace 'NOSPAM' with 'btinternet' in the reply address*****
"BBTACO" <BBTACO@SPAMNOT.COM> wrote in message
news:KeSdnaet8r3PNR_dRVn_iw@comcast.com...
>
> "BigBadger" <big_badger@NOSPAM.com> wrote in message
> news:c5t9u6$t5d$1@news7.svr.pol.co.uk...
> > That's normal, same thing here on XP Pro.
> >
> > --
> > *****Replace 'NOSPAM' with 'btinternet' in the reply address*****
> > "me" <davebarbs@sio.midco.net> wrote in message
> > news:1082kdu8kr3v1e9@corp.supernews.com...
> > > To all Wizards
> > >
> > > Main Issue: nForce2 SPP chipset drivers not recognized by Windows
XP
> > > Home Edition
> > >
> > > Following is my system configuration:
> > >
> > > NF7-S V2 motherboard
> > > Athlon XP 2800 processor, 333 front bus, not overclocked
> > > Bios number 23 (have used 20 and 21 with same results)
> > > Current nForce driver version 3.13, have used nforce driver that
> came
> > > with mb disk, same results
> > > Windows XP Home Edition, all updates installed. Windows was
> installed
> > > from a clean setup.
> > > ATA serial raid version 4.2.47, set up as a raid 0
> > > Hard drives, Seagate Barracuda 7200 80 gig.
> > > Memory, two Siemens 512 Meg DDR-SDRAM PC-3200, running at 400 MHZ.
> > Have
> > > tried 333 MHZ, and other ram sticks with same result.
> > > Memory modules set up in slots 2 and 3, upon boot "Dual DDR"
message
> > > displayed.
> > > Radeon 9600XT AGP video card, latest drivers.
> > > On board audio and LAN enabled, IEEE disabled.
> > >
> > > Problem:
> > >
> > > My Computer - System - Hardware - Device Manager- System Devices
> > >
> > > Basic display for computer hardware shows no conflicts, disabled
> > > devices, or other Windows warning icons.
> > >
> > > The following listed items have "No Drivers installed for this
> device"
> > > displayed when they are first selected in the "General" display box
for
> > each
> > > device:
> > > When I advance to the "Drivers Tab" display box, Windows lists
nVida
> > > drivers as being installed. All driver versions dates are 4/9/2003.
> > >
> > > nVidia nForce2 PCI System Management
> > > nVidia nForce2 Memory Controller (4 of these are listed)
> > > nVidia nForce 2 Ultra 400 Memory Controller
> > >
> > > When clicking on all other nForce devices, such as AGP devices,
Windows
> > > "General" display box says that drivers have been installed.
> > >
> > > Troubleshooting efforts to date:
> > >
> > > Two Clean installs of Windows. All Windows updates are installed.
> > Have
> > > tried three different BIOS versions. Have tried two different nForce
> > > unified driver versions. I have uninstalled the nForce drivers via
the
> > > Control Panel Remove Programs tab before installing new unified
drivers.
> > I
> > > have uninstalled each of the above items utilizing the Device manager,
> > then
> > > rebooted the computer and let the system find the new device and let
> > Windows
> > > install the driver. I have used the option in the BIOS of "Force
Update
> > > ESCD".
> > >
> > > Any suggestions on this problem are greatly appreciated. Thanks
in
> > > advance
> > >
> > > Dave
> > >
> > >
> >
> >
>
> I have XP Pro and an NF7-S ver. 2 and it shows five nVidia nForce2 Memory
> Controllers but none of them say nVidia nForce 2 Ultra 400 Memory
> Controller. Wonder why the Utra controller is not listed on mine?
>
>
 
Archived from groups: alt.comp.periphs.mainboard.abit (More info?)

"BigBadger" <big_badger@NOSPAM.com> wrote in message
news:c5ufp4$f8o$1@news5.svr.pol.co.uk...
> Mine says Ultra 400 just like the original poster...Are you running your
> memory dual channel?
>
> --
> *****Replace 'NOSPAM' with 'btinternet' in the reply address*****
> "BBTACO" <BBTACO@SPAMNOT.COM> wrote in message
> news:KeSdnaet8r3PNR_dRVn_iw@comcast.com...
> >
> > "BigBadger" <big_badger@NOSPAM.com> wrote in message
> > news:c5t9u6$t5d$1@news7.svr.pol.co.uk...
> > > That's normal, same thing here on XP Pro.
> > >
> > > --
> > > *****Replace 'NOSPAM' with 'btinternet' in the reply address*****
> > > "me" <davebarbs@sio.midco.net> wrote in message
> > > news:1082kdu8kr3v1e9@corp.supernews.com...
> > > > To all Wizards
> > > >
> > > > Main Issue: nForce2 SPP chipset drivers not recognized by
Windows
> XP
> > > > Home Edition
> > > >
> > > > Following is my system configuration:
> > > >
> > > > NF7-S V2 motherboard
> > > > Athlon XP 2800 processor, 333 front bus, not overclocked
> > > > Bios number 23 (have used 20 and 21 with same results)
> > > > Current nForce driver version 3.13, have used nforce driver that
> > came
> > > > with mb disk, same results
> > > > Windows XP Home Edition, all updates installed. Windows was
> > installed
> > > > from a clean setup.
> > > > ATA serial raid version 4.2.47, set up as a raid 0
> > > > Hard drives, Seagate Barracuda 7200 80 gig.
> > > > Memory, two Siemens 512 Meg DDR-SDRAM PC-3200, running at 400
MHZ.
> > > Have
> > > > tried 333 MHZ, and other ram sticks with same result.
> > > > Memory modules set up in slots 2 and 3, upon boot "Dual DDR"
> message
> > > > displayed.
> > > > Radeon 9600XT AGP video card, latest drivers.
> > > > On board audio and LAN enabled, IEEE disabled.
> > > >
> > > > Problem:
> > > >
> > > > My Computer - System - Hardware - Device Manager- System Devices
> > > >
> > > > Basic display for computer hardware shows no conflicts, disabled
> > > > devices, or other Windows warning icons.
> > > >
> > > > The following listed items have "No Drivers installed for this
> > device"
> > > > displayed when they are first selected in the "General" display box
> for
> > > each
> > > > device:
> > > > When I advance to the "Drivers Tab" display box, Windows lists
> nVida
> > > > drivers as being installed. All driver versions dates are 4/9/2003.
> > > >
> > > > nVidia nForce2 PCI System Management
> > > > nVidia nForce2 Memory Controller (4 of these are listed)
> > > > nVidia nForce 2 Ultra 400 Memory Controller
> > > >
> > > > When clicking on all other nForce devices, such as AGP devices,
> Windows
> > > > "General" display box says that drivers have been installed.
> > > >
> > > > Troubleshooting efforts to date:
> > > >
> > > > Two Clean installs of Windows. All Windows updates are
installed.
> > > Have
> > > > tried three different BIOS versions. Have tried two different
nForce
> > > > unified driver versions. I have uninstalled the nForce drivers via
> the
> > > > Control Panel Remove Programs tab before installing new unified
> drivers.
> > > I
> > > > have uninstalled each of the above items utilizing the Device
manager,
> > > then
> > > > rebooted the computer and let the system find the new device and let
> > > Windows
> > > > install the driver. I have used the option in the BIOS of "Force
> Update
> > > > ESCD".
> > > >
> > > > Any suggestions on this problem are greatly appreciated. Thanks
> in
> > > > advance
> > > >
> > > > Dave
> > > >
> > > >
> > >
> > >
> >
> > I have XP Pro and an NF7-S ver. 2 and it shows five nVidia nForce2
Memory
> > Controllers but none of them say nVidia nForce 2 Ultra 400 Memory
> > Controller. Wonder why the Utra controller is not listed on mine?
> >
> >
>
>
I switched my memory sticks to slots 2 and 3 so they are now running in dual
channel according to the boot up screen. But I still have the five nVidia
nForce2 Memory Controllers listed. None of them say Ultra 400 Memory
controller.
The general tab shows no driver installed like yours. But if I click on the
driver tab it shows Nvidia, 8/26/02, version 2.7.5.0. If I click on driver
details, it shows that no drivers have been installed or needed for this
device. Which one of the memory controllers on yours shows up as the Ultra
400?
 
Archived from groups: alt.comp.periphs.mainboard.abit (More info?)

BBTACO wrote:
<snip>
>>>
>>> I have XP Pro and an NF7-S ver. 2 and it shows five nVidia nForce2
>>> Memory Controllers but none of them say nVidia nForce 2 Ultra 400
>>> Memory Controller. Wonder why the Utra controller is not listed on
>>> mine?
>>>
>>>
>>
>>
> I switched my memory sticks to slots 2 and 3 so they are now running
> in dual channel according to the boot up screen. But I still have the
> five nVidia nForce2 Memory Controllers listed. None of them say
> Ultra 400 Memory controller.
> The general tab shows no driver installed like yours. But if I click
> on the driver tab it shows Nvidia, 8/26/02, version 2.7.5.0. If I
> click on driver details, it shows that no drivers have been installed
> or needed for this device. Which one of the memory controllers on
> yours shows up as the Ultra 400?

In device manager, the memory controllers (5) are listed as "NVIDIA
nForce2 Memory Controller". That is also normal.
 
Archived from groups: alt.comp.periphs.mainboard.abit (More info?)

>I have XP Pro and an NF7-S ver. 2 and it shows five nVidia nForce2 Memory
>Controllers but none of them say nVidia nForce 2 Ultra 400 Memory
>Controller. Wonder why the Utra controller is not listed on mine?

I think this is a specific driver thing. I have seen it listed that way before,
but it has changed with different drivers.
 
Archived from groups: alt.comp.periphs.mainboard.abit (More info?)

>In device manager, the memory controllers (5) are listed as "NVIDIA
>nForce2 Memory Controller". That is also normal.

Yes I have seen it both ways with different drivers. I don't think they would
have different drivers for having dual memory.
 
Archived from groups: alt.comp.periphs.mainboard.abit (More info?)

update your nforce drivers to the latest from nvidia ... I show the
"ultra400" version in device mgr ... I'm sure it appeared after updating
nforce drivers to v.3.13... the properties for my "ultra400 memory
controller", says I have v.3.38 driver.

cheers

"PRIVATE1964" <private1964@aol.com> wrote in message
news:20040418163305.25425.00000093@mb-m05.aol.com...
> >I have XP Pro and an NF7-S ver. 2 and it shows five nVidia nForce2
Memory
> >Controllers but none of them say nVidia nForce 2 Ultra 400 Memory
> >Controller. Wonder why the Utra controller is not listed on mine?
>
> I think this is a specific driver thing. I have seen it listed that way
before,
> but it has changed with different drivers.
 
You must log in or register to reply here.

TRENDING THREADS

Latest posts

Moderators online

Share this page

COMPANY
RESOURCES
FOLLOW
Top Bottom