Question PC is heavily underperforming and im tired of it

Jul 20, 2019
12
0
10
I'm tired of my pc running cs:go at barely 60 fps on low setting, gta v at around 40 and having lag issues in other games (Pes, FIFA, League of Legends ....)
My specs are :

Intel Core i7-7700HQ 2.80-3.80 GHz
NVIDIA GeForce GTX 1060 6GB
16 RAM

Please if you can give me advice on how to stop the lag i will b thankful.. The pc shouldnt have problems running the games cuz i compared the requirements..

I already set my NVIDIA as main gpu from nvidia control panel
 
You're trying to compare the performance of a laptop i7 to desktop systems, and that's just not going to be happen. MOST likely is the fact that you are experiencing thermal throttling issues, because that IS what happens on about 90% of laptops and notebooks when people use them for long term extended gaming sessions regardless of whether they were technically advertised as "gaming" laptops or not. They are simply NOT capable of providing adequate cooling continuously for extended periods of time the way people try to use them, ESPECIALLY when there are both high TDP processor and graphics adapters installed. They saturate the heat ceiling rather quickly and when left there for extended periods they tend to degrade rather rapidly.

Unfortunately, in my opinion, this is very likely to be the case here as well, because it is almost always the case, in most every case. Especially when the unit has been in use for about six months or longer and used for relatively heavy gaming for extended periods during that entire time. People who tend to use them on surfaces that are not 100% hard and flat, make the problem even worse by blocking off or restricting the cooling vents on the bottom and side which are needed to be kept clear for the cooling fans. So using them on your lap, on couches or sofas, on carpet, on bed clothes or any other surface other than a hard flat one, is an early death for a laptop.

Even if it's only used on that surface one time, it might be enough to create a thermal problem. Once you have a thermal problem on a laptop, you stand a good chance of always having a thermal problem on that unit.
 
  • Like
Reactions: Phaaze88
Jul 20, 2019
12
0
10
You're trying to compare the performance of a laptop i7 to desktop systems, and that's just not going to be happen. MOST likely is the fact that you are experiencing thermal throttling issues, because that IS what happens on about 90% of laptops and notebooks when people use them for long term extended gaming sessions regardless of whether they were technically advertised as "gaming" laptops or not. They are simply NOT capable of providing adequate cooling continuously for extended periods of time the way people try to use them, ESPECIALLY when there are both high TDP processor and graphics adapters installed. They saturate the heat ceiling rather quickly and when left there for extended periods they tend to degrade rather rapidly.

Unfortunately, in my opinion, this is very likely to be the case here as well, because it is almost always the case, in most every case. Especially when the unit has been in use for about six months or longer and used for relatively heavy gaming for extended periods during that entire time. People who tend to use them on surfaces that are not 100% hard and flat, make the problem even worse by blocking off or restricting the cooling vents on the bottom and side which are needed to be kept clear for the cooling fans. So using them on your lap, on couches or sofas, on carpet, on bed clothes or any other surface other than a hard flat one, is an early death for a laptop.

Even if it's only used on that surface one time, it might be enough to create a thermal problem. Once you have a thermal problem on a laptop, you stand a good chance of always having a thermal problem on that unit.
I dont think its overheating issue cuz i have very good cooling pad + my laptop has an extreme cooling system and my laptop is never hot
 
Cooling pads have ZERO effect on CPU or GPU core temperatures. None. Whatsoever. Ever. At all.

The only, ONLY thing a cooling pad does or even CAN do, is make the surface temperature of the laptop more bearable to the touch. That's it.

CPU and GPU core temperatures can rise and fall a matter of 60°C in seconds, and fall just as quickly, and are NOT affected much by outside factors EXCEPT for the sinking effect from a heatsink or water block that is in direct contact with the heat spreader that in turn is in direct contact with the internal die.
 
If there are any steps listed here that you have not already done, it would be advisable to do so if for no other reason than to be able to say you've already done it and eliminate that possibility.



First,

make sure your motherboard has the MOST recent BIOS version installed. If it does not, then update. This solves a high number of issues even in cases where the release that is newer than yours makes no mention of improving graphics card or other hardware compatibility. They do not list every change they have made when they post a new BIOS release.


Second,

go to the product page for your motherboard on the manufacturer website. Download and install the latest driver versions for the chipset, storage controllers, audio and network adapters. Do not skip installing a newer driver just because you think it is not relevant to the problem you are having. The drivers for one device can often affect ALL other devices and a questionable driver release can cause instability in the OS itself. They don't release new drivers just for fun. If there is a new driver release for a component, there is a good reason for it. The same goes for BIOS updates.


IF you have other hardware installed or attached to the system that are not a part of the systems covered by the motherboard drivers, then go to the support page for THAT component and check to see if there are newer drivers available for that as well. If there are, install them.


Third,

Make sure your memory is running at the correct advertised speed in the BIOS. This may require that you set the memory to run at the XMP profile settings. Also, make sure you have the memory installed in the correct slots and that they are running in dual channel which you can check by installing CPU-Z and checking the Memory and SPD tabs. For all modern motherboards that are dual channel memory architectures, from the last ten years at least, if you have two sticks installed they should be in the A2 (Called DDR4_1 on some boards) or B2 (Called DDR4_2 on some boards) which are ALWAYS the SECOND and FOURTH slots over from the CPU socket, counting TOWARDS the edge of the motherboard EXCEPT on boards that only have two memory slots total. In that case, if you have two modules it's not rocket science, but if you have only one, then install it in the A1 or DDR4_1 slot.



The last thing we want to look at,

for now anyhow, is the graphics card drivers. Regardless of whether you "already installed the newest drivers" for your graphics card or not, it is OFTEN a good idea to do a CLEAN install of the graphics card drivers. Just installing over the old drivers OR trying to use what Nvidia and AMD consider a clean install is not good enough and does not usually give the same result as using the Display Driver Uninstaller utility. This has a very high success rate and is always worth a shot.


If you have had both Nvidia and AMD cards installed at any point on that operating system then you will want to run the DDU twice. Once for the old card drivers (ie, Nvidia or AMD) and again for the currently installed graphics card drivers (ie, AMD or Nvidia). So if you had an Nvidia card at some point in the past, run it first for Nvidia and then after that is complete, run it again for AMD if you currently have an AMD card installed.



Also, if this is a "no signal detected" or other lack of visual display problem, it is probably a good idea to make sure the problem is not just a bad cable or the wrong cable IF this is a display issue. If it is NOT related to a lack of display signal, then obviously this part is not relevant to your issue.

This happens a lot. Try a different cable or a different TYPE of cable. Sometimes there can be issues with the monitor or card not supporting a specific specification such as HDMI 1.4 vs HDMI 2.0, or even an HDMI output stops working but the Displayport or DVI output still works fine on the graphics card. Always worth checking the cable and trying other cables because cables get run over, bent, bent pins or simply were cheap quality to begin with and something as simple as trying a different cable or different monitor might be all that is required to solve your issue.
 
Jul 20, 2019
12
0
10
If there are any steps listed here that you have not already done, it would be advisable to do so if for no other reason than to be able to say you've already done it and eliminate that possibility.



First,

make sure your motherboard has the MOST recent BIOS version installed. If it does not, then update. This solves a high number of issues even in cases where the release that is newer than yours makes no mention of improving graphics card or other hardware compatibility. They do not list every change they have made when they post a new BIOS release.


Second,

go to the product page for your motherboard on the manufacturer website. Download and install the latest driver versions for the chipset, storage controllers, audio and network adapters. Do not skip installing a newer driver just because you think it is not relevant to the problem you are having. The drivers for one device can often affect ALL other devices and a questionable driver release can cause instability in the OS itself. They don't release new drivers just for fun. If there is a new driver release for a component, there is a good reason for it. The same goes for BIOS updates.


IF you have other hardware installed or attached to the system that are not a part of the systems covered by the motherboard drivers, then go to the support page for THAT component and check to see if there are newer drivers available for that as well. If there are, install them.


Third,

Make sure your memory is running at the correct advertised speed in the BIOS. This may require that you set the memory to run at the XMP profile settings. Also, make sure you have the memory installed in the correct slots and that they are running in dual channel which you can check by installing CPU-Z and checking the Memory and SPD tabs. For all modern motherboards that are dual channel memory architectures, from the last ten years at least, if you have two sticks installed they should be in the A2 (Called DDR4_1 on some boards) or B2 (Called DDR4_2 on some boards) which are ALWAYS the SECOND and FOURTH slots over from the CPU socket, counting TOWARDS the edge of the motherboard EXCEPT on boards that only have two memory slots total. In that case, if you have two modules it's not rocket science, but if you have only one, then install it in the A1 or DDR4_1 slot.



The last thing we want to look at,

for now anyhow, is the graphics card drivers. Regardless of whether you "already installed the newest drivers" for your graphics card or not, it is OFTEN a good idea to do a CLEAN install of the graphics card drivers. Just installing over the old drivers OR trying to use what Nvidia and AMD consider a clean install is not good enough and does not usually give the same result as using the Display Driver Uninstaller utility. This has a very high success rate and is always worth a shot.


If you have had both Nvidia and AMD cards installed at any point on that operating system then you will want to run the DDU twice. Once for the old card drivers (ie, Nvidia or AMD) and again for the currently installed graphics card drivers (ie, AMD or Nvidia). So if you had an Nvidia card at some point in the past, run it first for Nvidia and then after that is complete, run it again for AMD if you currently have an AMD card installed.



Also, if this is a "no signal detected" or other lack of visual display problem, it is probably a good idea to make sure the problem is not just a bad cable or the wrong cable IF this is a display issue. If it is NOT related to a lack of display signal, then obviously this part is not relevant to your issue.

This happens a lot. Try a different cable or a different TYPE of cable. Sometimes there can be issues with the monitor or card not supporting a specific specification such as HDMI 1.4 vs HDMI 2.0, or even an HDMI output stops working but the Displayport or DVI output still works fine on the graphics card. Always worth checking the cable and trying other cables because cables get run over, bent, bent pins or simply were cheap quality to begin with and something as simple as trying a different cable or different monitor might be all that is required to solve your issue.
I actually already tried to update my BIOS and i get this error : mount the EFI system partition fail