Please Help!!! NO DISPLAY

[Tjm999]

Hello So I was making my first computer by myself and I used a anti static strap and all that jazz. I made sure everything went in the right way but for some reason I do not get a display. The first time I booted I got one and then now that I have my OS it wont even give me a display.
here is my build
CPU: i-5 4690k
GPU: N/A
Memory: 8gb Fury 1866
Motherboard: MSI B85M Gaming 1600MHZ
SSD: Kingston 240gb
PSU: 500w EVGA
the only problems I can think of is that the 4+20 adapter the 4 pin wont go all the way down and also that the memory clock speed is higher than the motherboard takes.. Please help me I reseated all of the parts but I will try anything.
Thanks!

 

[alexoiu]

Hi, Let's check firstly the BIOS version. What are the 4 digits after B in the board's serial (B14..)?

 

[Tjm999]

Hi sorry I can't find exactly what your looking for it just Says MSI B85M Gaming where on the box would it say?

 

[alexoiu]

There should be a barcode sticker with S/N

 

[Tjm999]

my SN is 601 7823 150b1408033340

 

[alexoiu]

CPU is supported.
Try clearing the CMOS (unplug the power cord and remove the CMOS battery for a minute). Leave single RAM module installed, start the board and see if helping.

 

[Tjm999]

Ok so i have the following parts plugged in. 1 stick of ram in the 1st slot (tried both), rook out the CMOS for 60 seconds, made sure 20+4 pin is all together and flush, made sure I had the right cpu cord plugged in. Have my SSD with sata in, and the wires coming from the case itself like the audio and usb etc. I still dont even get a signal detecting. I have tried HDMI and VGA but also to not I do not get any USB power
Thanks for your help so far hopefe can get to the bottom of this.,
.

 

[alexoiu]

Using a monitor or TV? Do you have a case speaker for attaching it to the motherboard (for beeps)?

 

[Tjm999]

I have tried using a monitor and a TV but I have something called "hd audio" coming from my case I just have no idea where to put it

 

[Tjm999]

And I know that both displays are good because I am on here with one and playing PS4 on the other.

 

[alexoiu]

By case speaker I mean http://images17.newegg.com/is/image/newegg/12-201-032-TS?$S300W$

 

[Tjm999]

no I do not have one of thiose

 

[alexoiu]

You need one, for checking if the CPU does work. Or simply RMA the board and hopefully the new one will work.

 

[Tjm999]

Can I get one at like radioshack? and where does it go in this board because I didn't see anything on it in the motherboard manual

 

[alexoiu]

Yes, sure. It gets connected to the front panel header (where power and reset buttons get connected to the board.

 

[Tjm999]

So here is the backside of the power and reset.
imgur.com/6smmsfu
imgur.com/NA4kkkg

 

[Tjm999]

or would it be on the board like this?
imgur.com/bxCnqDo

 

[alexoiu]

Yes, last picture. it goes to buz/spk

 

[Tjm999]

So it says in my manual that the JFP1 and JFP2 are the system panel connectors but JFP1 is full and JFP2 doesnt look like that here is what my problem is. The cables are plugged into JFP1, imgur.com/a/1TOJM

 

[Tjm999]

Where is the bus/spk?

 

[alexoiu]

imgur.com/bxCnqDo
In JFP2, use either BUZ+BUZ-, or SPK+, SPK-
It depends on the speaker connector.

 

[Tjm999]

will this speaker do? http://www.radioshack.com/pc-board-12vdc-70db-piezo-buzzer/2730074.html#.VJ2Ull4AA and what pins will work?

 

[Tjm999]

No where on JFP2 does it say BUZ or SPK

 

[alexoiu]

will this speaker do? http://www.radioshack.com/pc-board-12vdc-70db-piezo-buzzer/2730074.html#.VJ2Ull4AA and what pins will work?

I can't see its connector. Better: http://www.newegg.com/Product/Product.aspx?Item=N82E16812201032

No where on JFP2 does it say BUZ or SPK

Check imgur.com/bxCnqDo

 

[Tjm999]

SO I see a SPK+ and a BUZ+ and BUZ- is there anyway you can find me one at radio shack?