[SOLVED] Ryzen 7 7800X3D will not transfer heat, it overheats at idle ?

[hi2011090536]

Hello, I just finished building my girlfriends new PC. The ryzen processor we went with is the ryzen 7 7800x3d and I paired it with a cooler master ml240l ARGB AIO cooler. It will not cool at all. It starts at around 68 degrees Celsius and will slowly rise to high 80s and break 90 after only about 4 minutes uptime. If I leave it on it will pass 100 and turn itself off. (Only let that happen once by accident)

I have re applied thermal paste, tried a different type of paste, loosened and tightend the pump, flipped directions so the in/outlets are under the pump to help with gravity, updated bios, swapped the AIO with another one and even tried undervolting the cpu per an efficiency guide i followed on YouTube. Nothing makes a difference.

I'm in need of some guidance and hopefully someone knows what's going on. The last thing I can think of is maybe somethings not right under the cpu lid and Maybe it's not allowing the cpu to transfer hear properly? I don't know if that's how that works but the reason I saw that is because the tubes don't feel warm so I don't think the water is even heating up from it. I'm extremely stumped and would accept any assistance haha, thank you ☹️

Ryzen 7 7800X3D
Coolermaster ml240l argb
Corsair vengeance 32gb 6400mhz
Asrock b650m-hdv/m.2
Powercolor red devil 5700xt

 

[kanewolf]

Hello, I just finished building my girlfriends new PC. The ryzen processor we went with is the ryzen 7 7800x3d and I paired it with a cooler master ml240l ARGB AIO cooler. It will not cool at all. It starts at around 68 degrees Celsius and will slowly rise to high 80s and break 90 after only about 4 minutes uptime. If I leave it on it will pass 100 and turn itself off. (Only let that happen once by accident) I have re applied thermal paste, tried a different type of paste, loosened and tightend the pump, flipped directions so the in/outlets are under the pump to help with gravity, updated bios, swapped the AIO with another one and even tried undervolting the cpu per an efficiency guide i followed on YouTube. Nothing makes a difference. I'm in need of some guidance and hopefully someone knows what's going on. The last thing I can think of is maybe somethings not right under the cpu lid and Maybe it's not allowing the cpu to transfer hear properly? I don't know if that's how that works but the reason I saw that is because the tubes don't feel warm so I don't think the water is even heating up from it. I'm extremely stumped and would accept any assistance haha, thank you ☹️

Ryzen 7 7800x3d
Coolermaster ml240l argb
Corsair vengeance 32gb 6400mhz
Asrock b650m-hdv/m.2
Powercolor red devil 5700xt

It is not possible that you forgot to take any packing plastic off the heat sink before attaching to the CPU is there ?
There is a big "remove label before install", but people have left the plastic film on before ...

 

[hi2011090536]

It is not possible that you forgot to take any packing plastic off the heat sink before attaching to the CPU is there ?
There is a big "remove label before install", but people have left the plastic film on before ...

I've seen lots of people do that haha, I definitely made sure to remove that and the socket cover as well

 

[CountMike]

I've seen lots of people do that haha, I definitely made sure to remove that and the socket cover as well

Are you sure pump is running ? Hoses are well insulated but you should feel radiator getting warm.

 

[TerryLaze]

I have re applied thermal paste,

Did it look like the old paste was spread out correctly?!
If it doesn't make good contact it won't cool.

 

[hi2011090536]

Are you sure pump is running ? Hoses are well insulated but you should feel radiator getting warm.

Yes, I can hear the water start to move on startup for both AIOs, and the radiator won't warm up for either thats why I am so confused

 

[hi2011090536]

Did it look like the old paste was spread out correctly?!
If it doesn't make good contact it won't cool.

Absolutely, very even spread that had good coverage of the whole CPU

 

[TerryLaze]

Absolutely, very even spread that had good coverage of the whole CPU

To be clear, I don't mean the spread that you applied but the pressure pattern left by the previous installation. If when you removed the cooler the paste was undisturbed and exactly as you applied it then the cooler didn't make any contact to the paste.

 

[hi2011090536]

To be clear, I don't mean the spread that you applied but the pressure pattern left by the previous installation. If when you removed the cooler the paste was undisturbed and exactly as you applied it then the cooler didn't make any contact to the paste.

Yes sorry, I had done an x spread and after taking the cooler off it was an even squish I should say instead of spread haha

 

[kanewolf]

Yes sorry, I had done an x spread and after taking the cooler off it was an even squish I should say instead of spread haha

Do the temps in the BIOS match the other observations ?

 

[hi2011090536]

Do the temps in the BIOS match the other observations ?

Yes, I have also cross referenced between HW monitor and the Ryzen software and they all say the same. I can watch it rise the same from the bios.

 

[kanewolf]

Yes, I have also cross referenced between HW monitor and the Ryzen software and they all say the same. I can watch it rise the same from the bios.

I think, if it were me, I would switch to a good air cooler and see what happens. I am not a fan of AIO coolers.

 

[drivinfast247]

Is the pump set to 100% DC in the BIOS?

 

[hi2011090536]

I think, if it were me, I would switch to a good air cooler and see what happens. I am not a fan of AIO coolers.

I think I'll try that and see. I'll see about picking something up and test that

 

[hi2011090536]

Is the pump set to 100% DC in the BIOS?

I am not actually sure. Do you know where that would be located on an Asrock boards bios?

 

[drivinfast247]

I am not actually sure. Do you know where that would be located on an Asrock boards bios?

Fan or cooling.

 

[ohio_buckeye]

As far as air I do like the Thermalright peerless assassin. For the money it might be worth a shot.

 

[Kona45primo]

Perhaps an air bubble has blocked the water. Any chance you can try and angle it so the pump is under the hoses and rad to see if it can be jarred out?

 

[hi2011090536]

Fan or cooling.

Dude I think you're a genius and my girlfriends favorite person of the year. Under HW monitor on the bios all the fans including CPU FAN1 SETTING were ALL set to silent. I watched it rise to 75, enabled them all to performance and BOOM the temp dropped to 50 then 45, and now it was slowly dropping half a degree till its stable at 43 degrees Celsius, idling in the bios. YOURE A LIFE SAVE THANK YOU SO MUCH, I dont know why they were preset to that but I had no clue THANK YOU

 

[drivinfast247]

Dude I think you're a genius and my girlfriends favorite person of the year. Under HW monitor on the bios all the fans including CPU FAN1 SETTING were ALL set to silent. I watched it rise to 75, enabled them all to performance and BOOM the temp dropped to 50 then 45, and now it was slowly dropping half a degree till its stable at 43 degrees Celsius, idling in the bios. YOURE A LIFE SAVE THANK YOU SO MUCH, I dont know why they were preset to that but I had no clue THANK YOU

Glad to hear!

FYI: the 7XXX series will boost all the way to the thermal limit. So high spikes are pretty much normal.