wiring in usb3 on 8kra2+

[Guest]

Archived from groups: alt.comp.periphs.mainboard.epox (More info?)

i've just purchased an addon USB/1394 connector for a floppy bay but the
connectors arent the block type but single plug-in wires (chieftec special).
the problem is that the wiring in the manual is different to the diagram for
the add-on card.
1 2 1 6
3 4 2 7
5 6 8KRA2+ 3 8 Chieftec diagram
7 8 4 *
* 10 5 10

anyone have done this before and which wires go were. which is the
overload????? and what is difference between +5v and vcc and which goes
where.

Robin

 

[Guest]

Archived from groups: alt.comp.periphs.mainboard.epox (More info?)

Hi, Vcc is the +5VDC line on USB. Epox should have wiring in manual of the
onboard USB ports or in support section of www.epox.com Dont worry if you
don't have enough ground wires, one on each USB port is fine, so long as D-,
D+ and VCC(5VDC) are on the right pins. Don't know what you mean by
overload...




doug
www.lynncomp.com

"ROBIN GORDON" <robin@gordon3433.freeserve.co.uk> wrote in message
news:gPDfc.15$881.5@newsfe1-win...
> i've just purchased an addon USB/1394 connector for a floppy bay but the
> connectors arent the block type but single plug-in wires (chieftec
special).
> the problem is that the wiring in the manual is different to the diagram
for
> the add-on card.
> 1 2 1 6
> 3 4 2 7
> 5 6 8KRA2+ 3 8 Chieftec diagram
> 7 8 4 *
> * 10 5 10
>
> anyone have done this before and which wires go were. which is the
> overload????? and what is difference between +5v and vcc and which goes
> where.
>
> Robin
>
>

 

[Guest]

Archived from groups: alt.comp.periphs.mainboard.epox (More info?)

"ROBIN GORDON" <robin@gordon3433.freeserve.co.uk> wrote in message
news:gPDfc.15$881.5@newsfe1-win...
> i've just purchased an addon USB/1394 connector for a floppy bay but the
> connectors arent the block type but single plug-in wires (chieftec
special).
> the problem is that the wiring in the manual is different to the diagram
for
> the add-on card.
> 1 2 1 6
> 3 4 2 7
> 5 6 8KRA2+ 3 8 Chieftec diagram
> 7 8 4 *
> * 10 5 10
>
> anyone have done this before and which wires go were. which is the
> overload????? and what is difference between +5v and vcc and which goes
> where.

It would be better to refer to the wires by name.

Vcc and 5V are the same thing.


--
Graham W http://www.gcw.org.uk/ PGM-FI page updated, Graphics Tutorial
WIMBORNE http://www.wessex-astro-society.freeserve.co.uk/ Wessex
Dorset UK Astro Society's Web pages, Info, Meeting Dates, Sites & Maps
Change 'news' to 'sewn' in my Reply address to avoid my spam filter.

 

[Guest]

Archived from groups: alt.comp.periphs.mainboard.epox (More info?)

Robin

Page 3-14 of the manual has the PIN layout of the motherboard.
ftp://ftp.epox.com/downloads/Manual/mu-8kra2I&+10.pdf

--

=========================================================
Technical Support Department
EPoX International, Inc.
support@epox.com
www.epox.com
=========================================================

Visit the EPoX store for all those hard to find motherboard accessories...
BIOS chips, heatsinks, cables, and much more! https://www.epoxstore.com

"ROBIN GORDON" <robin@gordon3433.freeserve.co.uk> wrote in message
news:gPDfc.15$881.5@newsfe1-win...
> i've just purchased an addon USB/1394 connector for a floppy bay but the
> connectors arent the block type but single plug-in wires (chieftec
special).
> the problem is that the wiring in the manual is different to the diagram
for
> the add-on card.
> 1 2 1 6
> 3 4 2 7
> 5 6 8KRA2+ 3 8 Chieftec diagram
> 7 8 4 *
> * 10 5 10
>
> anyone have done this before and which wires go were. which is the
> overload????? and what is difference between +5v and vcc and which goes
> where.
>
> Robin
>
>