Recent content by loginuser

I want to buy a computer case, and I want to know which one to buy. I bought all my other parts with a silent/very quiet pc in mind, and I know that a good case will help reduce noise. The only cases that are available to me are: NZXT Phantom full tower and NZXT Phantom 530. The full tower comes...

Hi! I'm looking for a case that is either silent or very quiet, I have chosen all my other parts to be quiet, and I know that a good case will reduce noise. The cases that I can choose from are: 1/ NZXT PHANTOM 410 BLACK 2/ AEROCOOL XPREDATOR DEVIL RED 3/ COOLER MASTER HAF 922 4/ NZXT PHANTOM...

So I want to buy a kit of 2*8 Gb of ram, so I can leave the other two slots for future upgrades. The ram kit is rated at : 1600mhz cl10 at 1.5v. I read if I add one more kit of ram this will run only at 1333hmz and wont boot at 1600mhz, is this true ? I know that I should have in a dual channel...

it's noctua nh-u12p which also has adjustable fan. I would have bough the Ripjaws x cl10 since it fit under the heat sink without adjusting the fan, but from newegg it has a high rate of failure compared to the same model Ripjaws x cl9.

the sniper is little bit tall to fit under my cpu cooler. what about [ G.skill ripjaws x pc3-12800 CL10 2X8GB ] and [ Kingston Hyperx Beast pc3-12800 CL9 2X8GB ] is there going to be any difference in speed regarding CL9 in kingston vs CL10 in G.Skill ?

I can get these two rams at the same price, I know from the specs the cl9 is better than cl11 since they have the same frenquecy,So which one should I go with ? They both run at 1.65v. I only want to use them at 1.5V, is it possible to lower the voltage, and what will be the frenquency and LC...

Hi! I want to know if G.Skill Ripjaws X can fit with Noctua NH-U12P, from G.Skill website the Ripjaws X height is 40 mm, where as the noctua website said the max memory that can fit under Noctua NH-U12P is 40 mm. If anyone with both Noctua and G.Skill ram confirm either it will fit or not...

no I didn't buy the noctua yet, I just want to make sure I can control it's speed using one of the chassis fan header before I purchase it. So I will be able to control the fan speed by changing the voltage or what ?

I didn' buy the motherboard yet, so I can't check if it's eDP or LVDS using your method, if someone using the same motherboard can confirm whether it's eDP or LVDS it would be much appreciated.

the chassis fan header have 4 pins, so is it possible to control the noctua fan using this header even if it's 4 pins ? if yes, then how come the cpu_fan header with 4-pins can't control the noctua fan, whereas the chassis fan header can ? I know that cpu_fan header on asus p8z77-v can't control...

Hi! I want to know what is the type of displayport on Asus P8Z77-V is it eDP or LVDS, because I want to connect three monitors using my iGPU intel hd 4000, and intel says that the built-in display must be an Embedded DisplayPort1 (eDP) not a LVDS. My cpu is i5-3570k.

I know that Noctua NH-D14 comes with two fans that have only 3 pins, whereas the asus p8z77-v motherboard cpu fan can only be controller using PWM. so I guess the Noctua fan will always run 100% in this case. Is there any method that I can use to avoid having the cpu fan running at full speed...

SeaSonic is not on sale on my local store. they only have corsair psu, like TX750 v2, HX650, AX750 , AX760. which are Seasonic OEM. I was asking about asus anti surge conflicting with Corsair psu (like AX750) this is what I read from other forums, and I want to be sure before purchasing it...