Question Automatic Repair Couldn’t Repair Your PC

[rodmanii]

Recently i turned on my pc and was face with an automatic repair from windows only for this repair to end up failing with the following message:
"Automatic Repair Couldn’t Repair Your PC", offering to shut down or to use advanced options

after that, i just shut it down, turn it on again and then it worked normally, and restarted it a few times and it keep working as expected, what could be the reason for such behavior?

Operating System
Windows 11 Pro 64-bit
CPU
AMD Ryzen 9 7900 51 °C
Raphael 5nm Technology
RAM
64.0GB Dual-Channel Unknown @ 2395MHz (40-40-40-76)
Motherboard
ASRock B650M Pro RS (AM5) 20 °C
Graphics
M27Q (2560x1440@59Hz)
4087MB NVIDIA GeForce RTX 4070 Ti SUPER (MSI) 38 °C
512MB ATI AMD Radeon Graphics (ASRock)
SLI Disabled
CrossFire Disabled
Storage
1863GB KINGSTON SNV2S2000G (SATA-2 (SSD))
1863GB KINGSTON SNV2S2000G (SATA-2 (SSD))

 

[Ralston18]

PSU: make, model, wattage, age, condition (original to build, new, used, refurbished)?

Disk drive(s): make, model, capacity, how full?

= == =

Likely some small glitch.

When Windows was restarted it was able to find and fix the problem.

Two things to do:

1) Take a look in Reliability History/Monitor for any error codes, warnings, or informational events just before or at the time the noted failure.

2) If not already doing so, ensure that all important data is being backed up at least 2 x to other locations away from the system in question. Verify that the backups are recoverable and readable.

Also FYI: "dism" and "sfc /scannow".

https://www.windowscentral.com/how-use-dism-command-line-utility-repair-windows-10-image

https://www.lifewire.com/how-to-use-sfc-scannow-to-repair-windows-system-files-2626161

Just keep an eye on things and post any other errors or happenings.

 

[rodmanii]

the psu is a
XPG COREREACTOR II 1000W 80 PLUS
is the original to the build

the disk are
two M.2 KINGSTON 2TB NV2 PCI-E 4.0

c: partition has 1.72 TB available
f: partition has 1.35 TB available

i already run dism, sfc and chkdsk

 

[Bob.B]

the psu is a
XPG COREREACTOR II 1000W 80 PLUS
is the original to the build

the disk are
two M.2 KINGSTON 2TB NV2 PCI-E 4.0

c: partition has 1.72 TB available
f: partition has 1.35 TB available

i already run dism, sfc and chkdsk

Just to take a look run a pass of crystal disk info and post a screenshot for each disk.

 

[rodmanii]

Just to take a look run a pass of crystal disk info and post a screenshot for each disk.

https://imgur.com/a/7F20CbR

 

[Bob.B]

https://imgur.com/a/7F20CbR

Why is you C drive run x2 mode?

 

[rodmanii]

Why is you C drive run x2 mode?

i dont know, i chose the components but the store staff put the build together and installed windows, it shouldnt be like that?

 

[Bob.B]

i dont know, i chose the components but the store staff put the build together and installed windows, it shouldnt be like that?

If m.2 socket 3 is being used you might want to move the disk to a different m.2 socket.

 

[rodmanii]

If m.2 socket 3 is being used you might want to move the disk to a different m.2 socket.

what would be the effect of doing such thing?

 

[Bob.B]

what would be the effect of doing such thing?

Moving from a x2 slot to a x4 slot will double the speed.

Will you see a diff?.......maybe.