Freezing / hardware issues

Page 2 - Seeking answers? Join the Tom's Hardware community: where nearly two million members share solutions and discuss the latest tech.

bags159

Distinguished
Jul 7, 2011
37
0
18,530
Hello, I just finished my build of my new pc and it has been freezing constantly and my network card keeps failing to work.

750w corsair TX enthusiast V2 non modular
i5-2500k @ 3.3
MSI Z68A-G45-G3
Gskill 8gb ddr 3 1600 mhz 9-9-924 (running at 11-11-11-28 atm, had it at proper timings and same issues)
Xigamatek 1283SD cooler
MSI 460 GTX 1 GB
7200 rpm 1TB seagate
5400 rpm 230GB WD
LG basic CD/DVD burner/reader
Corsair Carbide 500r
Win7 64 bit professional

I have reformatted twice but my performance is very sluggish at times. IT runs games fine, but a lot of time when I try to multitask things will freeze up for 20 - 30 seconds. My network card will also tend to fail at these times and I need to reboot to get it to work (it doesn't detect networks and windows says the adapter is not recognized). Windows Explorer also crashes or locks up if I try to do anything immediately after booting.

I have the ram in the right slots, and nothing is overclocked besides the card that came pre-overclocked. The HDs and GPU were reused from my old computer that ran fine, but slow due to its age. Everything else is brand new.

I have tried running the PC with 1 stick of ram, switching both out, same results with either stick as the only stick in the first slot. Tried to run it without the network card, same problems.

I have also formatted and reinstalled windows 7 twice, same issue persists.

Strangely enough, my game performance is fine as long as I don't do anything but play the game.

What should I do?
 


lright, stopped BSRT and am now doing that.

How exactly do I run it? I rn the application, but I don't know what settings or anything.
 
t6r09s.png


Also, running the bart's test gave me an error on C;/ saying the system could not find the path specified when 4% done
 
http://www.z-a-recovery.com/man-smart.htm
" this attribute typically indicates that something is wrong with the connectors and/or cables. Disk-to-host transfers are protected by CRC error detection code when Ultra-DMA 66 or 100 is used. So if the data gets garbled between the disk and the host machine, the receiving controller senses this and the retransmission is initiated. Such a situation is called "UDMA CRC error". Once the problem is rectified (typically by replacing a cable), the attribute value returns to the normal levels pretty quick."
Also, all three of your HDDs wouldn't have to be problematic. Only your boot drive would have to have trouble.
 
I ran HD tune's scan, no damage all green boxes

@ kaja: oh so my HD has a bad sata cable? or slot?


edit: alright, i switched the cables into a different slot; no joy. Means it's the cable. I unfortunately cannot switch the cable out until tomorrow night due to no room because of a family xmas party!

Hoping that cable is the issue.
 
Cyclic redundancy check (CRC) is a method of verifying and correcting data after it is sent. What this warning is telling you is that at one point, data being sent/received by the drive failed this check.


------------

CRC Errors are usually when data gets corrupted between the HDD controller and SATA controller.


------------
UltraDMA CRC Error Count

The count of errors in data transfer via the interface cable as determined by ICRC (Interface Cyclic Redundancy Check).

That is what it means. Check to see if either:

A: your ports are going bad
B: Not enough voltage to the PCH
C: A bad cable

Use a different cable on a different port and see if the count stops rising.
 
In bios, PCH voltage is set to auto at 1.05v.

should i make it 1.06v like urs?

Edi:T hey thanks for the help, but I need to go to bed now. I'll be back in6 - 7 hours though.

Edit changed the voltage, nothing.