Hi!
My Specs:
CPU: AMD Ryzen 5 5600G
RAM: Corsair Vengeance DDR4 32 GB 3200 MHz
Motherboard: Gigabyte GA-B550M DS3H Rev 1.5
GPU: ASUS Phoenix RTX 3050
PSU: Corsair CX650M 80+ Bronze
Everything was running okay until one day I tried to install my old HDD. There was "No Signal" on my monitor but the Windows was booting up. So I removed the HDD and the problem didn't go away. I thought may be clearing CMOS would fix it but it didn't.
So I uninstalled my GPU and it was working perfectly through IGPU. So I thought it might be the dust and disassembled everything and dusted thoroughly especially the PCIE slot. Then I removed and inserted the CMOS battery and installed back the GPU. It worked for a few days and as I don't have any UPS the power cuts are also a problem. After one, it did the same issue. Then I researched and found out that Windows Boot Manager might be corrupted as well as the BIOS since it somewhat communicates with it. So after a few hours I saw it automatically corrected itself and worked for a few days before doing that again.
So I reinstalled windows and reflashed BIOS and I did this countless times along with battery reinstallation. I thought one of them - GPU or Mobo might be the problem. So I tried the GPU with my old mobo and there was no issue. So I thought my current mobo has problems but there is no issue with IGPU.
Then I found out that it gives a beep error message with CSM support disabled with GPU as if there is nothing installed in PCIE slot even when there is a GPU installed.
And currently I am not able to get the GPU to work. This is weird but when I switch on my PC after a few hours the GPU shows the mobo logo for a few seconds and then the monitor turns off. I tried flashing the BIOS with previous version (the version the release notes of which says "Addresses potential UEFI Vulnerabilities (LOGO fail)" but it is still the same.
I am unable to understand what is wrong . I have tried everything and I've run out of ideas.
Any help is greatly appreciated.
My Specs:
CPU: AMD Ryzen 5 5600G
RAM: Corsair Vengeance DDR4 32 GB 3200 MHz
Motherboard: Gigabyte GA-B550M DS3H Rev 1.5
GPU: ASUS Phoenix RTX 3050
PSU: Corsair CX650M 80+ Bronze
Everything was running okay until one day I tried to install my old HDD. There was "No Signal" on my monitor but the Windows was booting up. So I removed the HDD and the problem didn't go away. I thought may be clearing CMOS would fix it but it didn't.
So I uninstalled my GPU and it was working perfectly through IGPU. So I thought it might be the dust and disassembled everything and dusted thoroughly especially the PCIE slot. Then I removed and inserted the CMOS battery and installed back the GPU. It worked for a few days and as I don't have any UPS the power cuts are also a problem. After one, it did the same issue. Then I researched and found out that Windows Boot Manager might be corrupted as well as the BIOS since it somewhat communicates with it. So after a few hours I saw it automatically corrected itself and worked for a few days before doing that again.
So I reinstalled windows and reflashed BIOS and I did this countless times along with battery reinstallation. I thought one of them - GPU or Mobo might be the problem. So I tried the GPU with my old mobo and there was no issue. So I thought my current mobo has problems but there is no issue with IGPU.
Then I found out that it gives a beep error message with CSM support disabled with GPU as if there is nothing installed in PCIE slot even when there is a GPU installed.
And currently I am not able to get the GPU to work. This is weird but when I switch on my PC after a few hours the GPU shows the mobo logo for a few seconds and then the monitor turns off. I tried flashing the BIOS with previous version (the version the release notes of which says "Addresses potential UEFI Vulnerabilities (LOGO fail)" but it is still the same.
I am unable to understand what is wrong . I have tried everything and I've run out of ideas.
Any help is greatly appreciated.
Last edited: