P4P800 Deluxe: Can not see Intel raid during boot after bi..

[Guest]

Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

Hello,

I have a ASUS P4P800 Deluxe motherboard. I have updated the bios from 1014
to 1019, becuase I had problems with the boot priority sequence when using
USB harddisk device.

After I updated to bios version 1019 the boot screen for the Intel raid
controlles has disapeared.

The system disk is placed in a raid 1 on two S-ATA drives. The system starts
ok up on WinXPpro.

But it is not possibel to acces the Intel Raid controller during boot.

In the bios S-ATA is activated and boot-rom is enabled.

Can anyone help me with this problem (I works fine as it is, but it is not
possible to reconfigure my Intel raid during complete ney installation)?

Ragards

Jacob Jørgensen
Denmark

 

[Guest]

Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

you have to hit a key at boot up !
check the manual...


ñíñjà¤têç

-----END-PGP-SIGNATURE-----



On Tue, 15 Feb 2005 20:37:29 +0100, "Jacob Jørgensen"
<gismoREMOVE@12move.dk> wrote:

>Hello,
>
>I have a ASUS P4P800 Deluxe motherboard. I have updated the bios from 1014
>to 1019, becuase I had problems with the boot priority sequence when using
>USB harddisk device.
>
>After I updated to bios version 1019 the boot screen for the Intel raid
>controlles has disapeared.
>
>The system disk is placed in a raid 1 on two S-ATA drives. The system starts
>ok up on WinXPpro.
>
>But it is not possibel to acces the Intel Raid controller during boot.
>
>In the bios S-ATA is activated and boot-rom is enabled.
>
>Can anyone help me with this problem (I works fine as it is, but it is not
>possible to reconfigure my Intel raid during complete ney installation)?
>
>Ragards
>
>Jacob Jørgensen
>Denmark
>

 

[Guest]

Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

Hello,

Yes Ctrl+I, but the screen where it says press Ctrl+I to configure dosen't
come up!

Best regards

Jacob

"timmy" <timmy@teeta.net> skrev i en meddelelse
news:cbi511tbdghlqgcmh87f6roi1shhek0r68@4ax.com...
>
> you have to hit a key at boot up !
> check the manual...
>
>
> ñíñjà¤têç
>
> -----END-PGP-SIGNATURE-----
>
>
>
> On Tue, 15 Feb 2005 20:37:29 +0100, "Jacob Jørgensen"
> <gismoREMOVE@12move.dk> wrote:
>
>>Hello,
>>
>>I have a ASUS P4P800 Deluxe motherboard. I have updated the bios from 1014
>>to 1019, becuase I had problems with the boot priority sequence when using
>>USB harddisk device.
>>
>>After I updated to bios version 1019 the boot screen for the Intel raid
>>controlles has disapeared.
>>
>>The system disk is placed in a raid 1 on two S-ATA drives. The system
>>starts
>>ok up on WinXPpro.
>>
>>But it is not possibel to acces the Intel Raid controller during boot.
>>
>>In the bios S-ATA is activated and boot-rom is enabled.
>>
>>Can anyone help me with this problem (I works fine as it is, but it is not
>>possible to reconfigure my Intel raid during complete ney installation)?
>>
>>Ragards
>>
>>Jacob Jørgensen
>>Denmark
>>
>

 

[Paul]

Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

In article <4212d56e$0$29433$ba624c82@nntp06.dk.telia.net>, "Jacob
Jørgensen" <gismoREMOVE@12move.dk> wrote:

> Hello,
>
> Yes Ctrl+I, but the screen where it says press Ctrl+I to configure dosen't
> come up!
>
> Best regards
>
> Jacob
>

Have you tried "Load Setup Defaults" in the BIOS ?

Have you tried "Clearing the CMOS" (CLRTC jumper) ?

See the manual for the correct procedure - remember to
unplug the computer before doing the clear CMOS procedure,
to avoid the possibility of damage via the +5VSB supply.

Maybe one of those two options will make the RAID come back.
You will need to set up the BIOS options again, after
trying those two possible solutions. Write the custom BIOS
settings down on a piece of paper before proceeding.

Paul

 

[Guest]

Archived from groups: alt.comp.periphs.mainboard.asus (More info?)

I have tryed to load setup defaults!

I have not tried to clear my cmos and I don't wan't to do that, because I
know that if I flash back the 1014 bios the Intel Raid boot menu comes up
again during boot. Based on that I don't think that clearing the cmos will
help!

Any other ideas?

Regards

Jacob
"Paul" <nospam@needed.com> skrev i en meddelelse
news:nospam-1602051421250001@192.168.1.177...
> In article <4212d56e$0$29433$ba624c82@nntp06.dk.telia.net>, "Jacob
> Jørgensen" <gismoREMOVE@12move.dk> wrote:
>
>> Hello,
>>
>> Yes Ctrl+I, but the screen where it says press Ctrl+I to configure
>> dosen't
>> come up!
>>
>> Best regards
>>
>> Jacob
>>
>
> Have you tried "Load Setup Defaults" in the BIOS ?
>
> Have you tried "Clearing the CMOS" (CLRTC jumper) ?
>
> See the manual for the correct procedure - remember to
> unplug the computer before doing the clear CMOS procedure,
> to avoid the possibility of damage via the +5VSB supply.
>
> Maybe one of those two options will make the RAID come back.
> You will need to set up the BIOS options again, after
> trying those two possible solutions. Write the custom BIOS
> settings down on a piece of paper before proceeding.
>
> Paul