Samsung hd103sj

Page 2 - Seeking answers? Join the Tom's Hardware community: where nearly two million members share solutions and discuss the latest tech.
Status
Not open for further replies.

cesar509

Distinguished
May 2, 2011
12
0
18,510
Hello!

My samsung 1TB hdd has stopped spinning. I think its the pcb. I dont see/smell any burnt components. I have a second HDD of the same model and firmware but bought 6 months later. I checked the pcb and there is a 1 chip diff. One pcb is by Foxconn and the other FCI.

I have look everywhere and i can't find a pcb for it. Anyone who knows a site/store that sells hdd pcbs?
 
Solution
All those voltages look OK to me.

The Vneg voltage should be -5V. It supplies the negative voltage for the preamplifier chip inside the HDA. The preamp also needs +5V power from the SATA power conector.

The SDRAM and Atmel flash memory both require +2.5V. This is supplied by the uppermost DC-DC converter. The same Vio supply is also used by the Marvell MCU.

The lowermost DC-DC converter appears to provide the Vcore supply for the MCU. I would have guessed +1.2V, but your result is close enough. You could confirm these measurements by testing your replacement board.

That said, I think your only reasonable chance of a DIY repair is to find a board that is more closely matched. I don't know whether you will need to transfer the flash...

Your HDD have some error in service area and you must pay at least $5000 for proper tool. Don't try this at home. Go for DR in your local.
 

hello i need a pcb BF41-00303A 00 can you sell it to me ?
thank's
 
Sorry florpanama, but since I've no solution for my HDD BF41-00278A 00, I keep my hdd BF41-00303A 00.

I've just acquire a pcb BF41-00278A 00 in second hand. But whith this new pcb, the motor of my hard drive does not start. Here is the mesure I have made:

33o5pux.jpg


Is there a solution to make this pcb work ?
 
@paulolesgaz, your second hand PCB appears faulty. Without a Vcore voltage the MCU will be brain dead. I would measure the resistance of the coil, and I would also measure its resistance to ground.

The absence of the -5V supply is OK. In some designs the MCU needs to enable this supply by sending an appropriate command to the motor controller, so if the MCU is down, then the -5V will be missing.

 
Thanks fzabkar for your help.

Sorry, I don't understand well what I would measure. I did not represente which component is the coil on the pcb.

If this pcb is really faulty, there is no way to repair it ?
 
Hi,

I know this is an old thread, however ...

I have the same drive. It clicks around 10 times with about 2 clicks/second. Then it spins down.

I measured the voltage across the two diodes just next to the power connector. They showed +-12V and +-5V depending on the polarity.

I guess the diodes are dead then?

Can I replace them with any diode?

Thanks in advance 🙂

Martin
 
thanks, fzabkar. Do you have any advice?

I have read about the freezer trick, is this something I should consider?

Also: If I gently shake the drive while connected, I can make the clicking noise go away for some time and it takes longer before it spins down. Does that tell something?
 
Hi Paulolesgaz,

Sorry i never went back to this forum to check updates after my initial posts. I still have the HDDs that i posted but they are back in Manila. I'm now in Singapore.

were you able to fix your HDD issues?

cesar509



 
Did a PCB swap with two 2009.09 model and worked without issue [no need to replace the bios chip]. Replaced PCB disk recognized and fully usable.

I have another disk from the 2011.01 which I assume had a PCB failure as well. The disk does not power up when connected. I tried a PCB swap [with another 2001.01 model], motor spins up but did not hear head movements. Drive not recognized in bios so will try with a BIOS chip exchange.

Strangely enough the TVS diodes are OK and also the resistor. I followed also the measurements that fzabkar suggest and on one coil there is zero.

Is there a way to check the BIG chips ? maybe one of that is gone and can be replaced.
 
I have Samsung HD 252 HJ the problem is spins is fine voltage are on coils 2.5 & 1.2 respectively but there is no sign of HDD in USB mode when I connect it directly to Mother board PC the PC gives beep & don't start if any one has any suggestion plz reply
 
Status
Not open for further replies.