I have the following to my recollection
Asus ROG Strix X470-F
AMD Ryzen 5 2600X
GSKill Ripjaws 3200 2x8GB
Powercolor Red Devil RX 580 / 8GB
Storage
Inland SATA SSD 250 GB
Samsung 970 EVO NVME SSD 250GB
ADATA NVME SSD 500GB
Operating System Windows 10 Pro
Computer was working fine a day before. I clicked "Power" / Sleep and put the system in sleep. When I tried to weak up the system I could see it powered up, but the screen monitor was blank (black , showing nothing) . Pressed the power button for 4 seconds and powered off the system. When I powered on again, it POSTs OK and starts loading Windows and gets stuck in the loading screen with the dots going round and round forever.
I booted from a Windows 10 USB, went into repair mode and for few days I tried every option available to recover.
2 - when I installed on the SATA SSD, it did go through the first configuration setup, restart, and nothing , same dots going round and round.
When I started from the USB drive and went into the different repair menus I did opened the CMD mode and ran chkdsk on all these disks with no issues for any of them.
The only thing I could not run in CMD was the sfc scannow, with its options. It can not start the sfc scannow, even after I went in CMD and get the TrustedInstaller ( sc config trustedinstaller start= auto / Success/ net start trustedinstaller) - service started.
What else can I try before i get a new MB , CPU and build a new one?
One other issue to mention, and probably an important one, when I go in BIOS i can see the date in there is some date like year 3031. I changed it to current date , on the next boot , when I went to BIOS again, is shows again the year 3031 date. Any suggestions?
Asus ROG Strix X470-F
AMD Ryzen 5 2600X
GSKill Ripjaws 3200 2x8GB
Powercolor Red Devil RX 580 / 8GB
Storage
Inland SATA SSD 250 GB
Samsung 970 EVO NVME SSD 250GB
ADATA NVME SSD 500GB
Operating System Windows 10 Pro
Computer was working fine a day before. I clicked "Power" / Sleep and put the system in sleep. When I tried to weak up the system I could see it powered up, but the screen monitor was blank (black , showing nothing) . Pressed the power button for 4 seconds and powered off the system. When I powered on again, it POSTs OK and starts loading Windows and gets stuck in the loading screen with the dots going round and round forever.
I booted from a Windows 10 USB, went into repair mode and for few days I tried every option available to recover.
- system repair - does not work, every time I get the message that it could not perform a system repair.
- system restore - found 2 restore points, restored to the further one, it goes through the whole restore process, same thing on restart gets stuck on loading Windows.
- I removed the drives and connected one drive at a time - clean install of Windows 10 and issue still continue.
2 - when I installed on the SATA SSD, it did go through the first configuration setup, restart, and nothing , same dots going round and round.
When I started from the USB drive and went into the different repair menus I did opened the CMD mode and ran chkdsk on all these disks with no issues for any of them.
The only thing I could not run in CMD was the sfc scannow, with its options. It can not start the sfc scannow, even after I went in CMD and get the TrustedInstaller ( sc config trustedinstaller start= auto / Success/ net start trustedinstaller) - service started.
What else can I try before i get a new MB , CPU and build a new one?
One other issue to mention, and probably an important one, when I go in BIOS i can see the date in there is some date like year 3031. I changed it to current date , on the next boot , when I went to BIOS again, is shows again the year 3031 date. Any suggestions?