Recent content by valrog

  1. V

    Question 2 pc wired connection

    Im sorry im not that familiar with networking. So basically just one, i guess that answers my question. looks like i'll end up with powerline. TY!
  2. V

    Question 2 pc wired connection

    so theres really no other way than powerline? im not quite sure what moca is sorry. Ive tried looking up if having 2 modems in same network is possible and ive gotten mixed answers so im not quite sure on that too.
  3. V

    Question 2 pc wired connection

    The set up is one pc upstairs and another one downstairs but if possible would want both of them to have wired connection without having to run cables through the house. The main modem would be in the upstairs room but i have been told theres a connector thing too downstairs (same as the one...
  4. V

    [SOLVED] 2 diff pair of ram

    how though. do i have to manually set them to 2400 instead of xmp
  5. V

    [SOLVED] 2 diff pair of ram

    yeah i figured. Jus looking to see how i can set all of them to 1 speed though.
  6. V

    [SOLVED] 2 diff pair of ram

    ah okay that makes sense. So where do so that both pairs are running the same speed?
  7. V

    [SOLVED] 2 diff pair of ram

    hi so i have 2 diff pairs of ram in my system right now. theyre both the same gskill tridentz but diff speed. in slot 1 and 3 is the 3200mhz cl16 pair in slot 2 and 4 is the 2400mhz cl15 pair i turned on xmp profile in bios for 3200 cl16 (since its what was listed there) and so far i havent...
  8. V

    [SOLVED] ekwb a240g kit questions

    oh my bad. i thought i actually posted it in cooling section. So if im getting fittings and additional rad, it should both be aluminum? any good ones? I might be blind but all the rads i see from ekwb site is copper.. so im not sure what to buy.
  9. V

    [SOLVED] ekwb a240g kit questions

    So its on sale right now. i been meaning to start water cooling. Can i just buy this kit and just add onto it? maybe another rad + zmt tubes (i rly like them). and possibly some angled fittings. would this work?
  10. V

    Question rx 580 overheating issue

    Yeah its done right. screws are nice and tight and thermal paste is right amount. + if something was off i would assume the idle temps to be higher right. thats why im just so confused. Everything looks good aside from the fact that it just overheats once fps is uncapped.
  11. V

    Question rx 580 overheating issue

    oh sorry i forgot to mention that this was done on an open air testbench. so airflow wasnt really a problem or anything. and the rise of temp was kinda not normal. It went from the normal 55-60c all the way to 90c in a matter of like ~5-10secs after uncapping fps. Ive also thought of...
  12. V

    Question rx 580 overheating issue

    Hi so i have a rx 580. with the latest amd drivers. I have replaced the thermal paste on it and it idles at a good 25-30. when gaming (60fps capped) its 55-60c on avg temp. now the issue is when i uncap fps. so the fps will shoot to about 100-120fps. and the temps will rise to 90c-higher...
  13. V

    Question 2 different pair of ram kits

    Im at work right now but from what i can remember at the bottom right section where it shows the ram it shows the timings of what ive set in the bios. but does that mean all the ram sticks are running those timings then? or is there a way in hwinfo to see each stick's timing.
  14. V

    Question 2 different pair of ram kits

    So i have tridentz rgb at 3200mhz cl16. and another one at 2400mhz cl15. Im all 4 and was able to set xmp/docp profile at 3200mhz in bios. does that mean all 4 ram sticks are running at 3200mhz cl16 speed? if it matters, the 3200mhz cl16 kit is on slot 1/3 and the 2400mhz cl15 at 2/4
  15. V

    [SOLVED] RGB LED STRIPS

    im not sure what topic to ask this on sorry if this is the wrong thread. I have some extra led strips that i want to use on build but this build has a budget motherboard (literally only has 2 fan headers, cpu and sys lol). the ends of the rgb cables are i think 3/4pin crj (i think thats whats...