- Dec 30, 2018
- 2
- 0
- 10
After getting a Geforce GTX 1050 TI graphics card (Gigabyte Single Fan), I replaced the old graphics card which was a Palit Geforce GT 640 and turned it on.
Monitor Config:
2 1920x1080 Monitors to PCIE graphics (1050TI)
1 1440x900 Monitor to Intergrated Intel HD Graphics 530
I turned it on, it booted into Windows and only the intergrated graphics was on and taking a lot at device manager showed that ''Windows has stopped this device because it has reported problems. (Code 43)" and looking at the Problem Code "0000002B"
I've tried installing new and outdated drivers, uninstalling the driver for the old graphics card and the new that I installed, tried to make the BIOS show on the PCIE graphics by changing the IGPU to ON and changing the primary screen to the PCIE, which resulted to 1 long beep, 3 short (Video card not detected (reseat video card) or bad video card.) and a weird colour pattern on the intergrated graphics screen when Windows was booting up (When it was fully booted up, the screen was normal), tried to reseat the card, checking the fan to make sure that there was power to it (there was). All to no luck.
Spec:
Operating System
Windows 10 Pro 64-bit
CPU
Intel Core i3 6100 @ 3.70GHz
Skylake 14nm Technology
RAM
16.0GB Dual-Channel Unknown @ 1064MHz (15-15-15-36) (Crucial Memory)
Motherboard
ASUSTeK COMPUTER INC. H110M-A/M.2 (LGA1151)
Graphics
HP w1907 (1440x900@60Hz)
Intel HD Graphics 530 (ASUStek Computer Inc)
NVIDIA GeForce GTX 1050 Ti (Undefined) <----
ForceWare version: 417.35
SLI Disabled
PCIESLOT:
Slot Type PCI-E
Slot Usage In Use
Data lanes x16
Slot Designation PCIEX16
Characteristics 3.3V, Shared, PME
Slot Number 0
Graphics (Indepth):
NVIDIA GeForce GTX 1050 Ti
Manufacturer NVIDIA
Model GeForce GTX 1050 Ti
Device ID 10DE-1C82
Revision A2
Subvendor Undefined (0000)
Current Performance Level Level 0
Driver version 25.21.14.1735
Count of performance levels : 1
Level 1 - "Perf Level 0"
I'm starting to think that it is a hardware issue at this point.
Any suggestions?
Thanks.
Monitor Config:
2 1920x1080 Monitors to PCIE graphics (1050TI)
1 1440x900 Monitor to Intergrated Intel HD Graphics 530
I turned it on, it booted into Windows and only the intergrated graphics was on and taking a lot at device manager showed that ''Windows has stopped this device because it has reported problems. (Code 43)" and looking at the Problem Code "0000002B"
I've tried installing new and outdated drivers, uninstalling the driver for the old graphics card and the new that I installed, tried to make the BIOS show on the PCIE graphics by changing the IGPU to ON and changing the primary screen to the PCIE, which resulted to 1 long beep, 3 short (Video card not detected (reseat video card) or bad video card.) and a weird colour pattern on the intergrated graphics screen when Windows was booting up (When it was fully booted up, the screen was normal), tried to reseat the card, checking the fan to make sure that there was power to it (there was). All to no luck.
Spec:
Operating System
Windows 10 Pro 64-bit
CPU
Intel Core i3 6100 @ 3.70GHz
Skylake 14nm Technology
RAM
16.0GB Dual-Channel Unknown @ 1064MHz (15-15-15-36) (Crucial Memory)
Motherboard
ASUSTeK COMPUTER INC. H110M-A/M.2 (LGA1151)
Graphics
HP w1907 (1440x900@60Hz)
Intel HD Graphics 530 (ASUStek Computer Inc)
NVIDIA GeForce GTX 1050 Ti (Undefined) <----
ForceWare version: 417.35
SLI Disabled
PCIESLOT:
Slot Type PCI-E
Slot Usage In Use
Data lanes x16
Slot Designation PCIEX16
Characteristics 3.3V, Shared, PME
Slot Number 0
Graphics (Indepth):
NVIDIA GeForce GTX 1050 Ti
Manufacturer NVIDIA
Model GeForce GTX 1050 Ti
Device ID 10DE-1C82
Revision A2
Subvendor Undefined (0000)
Current Performance Level Level 0
Driver version 25.21.14.1735
Count of performance levels : 1
Level 1 - "Perf Level 0"
I'm starting to think that it is a hardware issue at this point.
Any suggestions?
Thanks.
Facebook
Twitter
Instagram