ISDN Wont Accept and Transfer PSTN Calls To CCM "bad beare..

[Guest]

Archived from groups: comp.dcom.voice-over-ip (More info?)

AS5350 Version 12.3(11)T2

I want to Transfer Calls From ISDN to CCM ,
The transfer call from PSTN to CCM doesn't work.
When I try I have a busy line.

I try this command on interface Serial3/0:15
"isdn incoming-voice Voice", but "voice" done % Invalid input detected

This is my config :
===================

version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname AS5350
!
boot-start-marker
boot system flash c5350-is-mz.123-11.T2.bin
no boot startup-test
boot-end-marker
!
enable secret
enable password
!
resource-pool disable
calltracker enable
calltracker history max-size 30
calltracker call-record verbose
spe default-firmware spe-firmware-1
no voice-fastpath enable
no aaa new-model
ip subnet-zero
!
ip cef
isdn switch-type primary-net5
isdn logging
!
voice service voip
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback cisco
cause-code legacy
h323
call start slow
!
fax interface-type fax-mail
!
controller E1 3/0
framing NO-CRC4
pri-group timeslots 1-16
!
interface Serial3/0:15
no ip address
isdn switch-type primary-net5
isdn send-alerting
isdn sending-complete
no cdp enable
!
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.30.20
no ip http server
!
map-class dialer test
dialer voice-call
!
control-plane
!
voice-port 3/0
bearer-cap 3100Hz
!
voice-port 3/1
!
no mgcp timer receive-rtcp
no mgcp explicit hookstate
!
dial-peer voice 3000 voip
destination-pattern T
session target ipv4:192.168.30.205
incoming called-number 9762
dtmf-relay h245-alphanumeric
codec g711ulaw
!
dial-peer voice 1 pots
destination-pattern 0T
direct-inward-dial
port 3/0
!
ss7 mtp2-variant Bellcore 0
ss7 mtp2-variant Bellcore 1
ss7 mtp2-variant Bellcore 2
ss7 mtp2-variant Bellcore 3
!
line con 0
line aux 0
line vty 0 4
password xxx
login
line 1/00 1/59
no flush-at-activation
modem InOut
!
scheduler allocate 10000 400
ntp clock-period 17180058
ntp server 64.112.189.11
end

The debug and the error :
=========================
AS5350#sh debug


The following ISDN debugs are enabled on all DSLs:

debug isdn error is ON.
debug isdn event is ON.
debug isdn q931 is ON. (filter is OFF)
debug isdn silent errors is ON.


AS5350#
*Jan 1 18:13:24.376: ISDN Se3/0:15 Q931: RX <- SETUP pd = 8 callref =
0x0014
Bearer Capability i = 0x9090A3
Standard = CCITT
Transer Capability = 3.1kHz Audio
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9838C
Exclusive, Channel 12
Progress Ind i = 0x8583 - Origination address is non-ISDN
Calling Party Number i = 0x1081, '37797912345'
Plan:Unknown, Type:International
Called Party Number i = 0x81, '9762'
Plan:ISDN, Type:Unknown
Sending Complete
*Jan 1 18:13:24.380: ISDN Se3/0:15 EVENT: process_rxstate: ces/callid
1/0x12 calltype 2 CALL_INCOMING
*Jan 1 18:13:24.380: ISDN Se3/0:15 EVENT: call_incoming: call_id
0x0012, Guid = Se3/0:15
*Jan 1 18:13:24.380: ISDN Se3/0:15 **ERROR**: call_incoming: Received a
call id 0x12 with a bad bearercap from 37797912345 on b channel 12
*Jan 1 18:13:24.380: ISDN Se3/0:15 EVENT: process_rxstate: ces/callid
1/0x12 calltype 2 CALL_CLEARED
*Jan 1 18:13:24.380: ISDN Se3/0:15 Q931: TX -> RELEASE_COMP pd = 8
callref = 0x8014
Cause i = 0x80D8 - Incompatible destination

 

[Guest]

Archived from groups: comp.dcom.voice-over-ip (More info?)

anonyme <ano@nyme.com> wrote in news:41fa209c$0$20494
$4d4eb98e@read.news.fr.uu.net:

> *Jan 1 18:13:24.380: ISDN Se3/0:15 **ERROR**: call_incoming: Received a
> call id 0x12 with a bad bearercap from 37797912345 on b channel 12

You're receiving calls with bearer capability data, but expecting only
voice?

--
Andreas

 

[Guest]

Archived from groups: comp.dcom.voice-over-ip (More info?)

Andreas Sikkema wrote:
> anonyme <ano@nyme.com> wrote in news:41fa209c$0$20494
> $4d4eb98e@read.news.fr.uu.net:
>
>
>>*Jan 1 18:13:24.380: ISDN Se3/0:15 **ERROR**: call_incoming: Received a
>>call id 0x12 with a bad bearercap from 37797912345 on b channel 12
>
>
> You're receiving calls with bearer capability data, but expecting only
> voice?
>
Hi Andreas,

Yes, for the moment I want only receive voice call

Thanks in advance