Question Processors with a frame instead of a lid

[demoncheg]

AMD draw a processor with a frame for flow cooling, but produce it with a lid.

 

[Ralston18]

Your question is not clear.

Please provide more information and detail about what you are planning or attempting to do.

Are you able to take and post photographs?

Photographs and screenshots can be posted here via imgur (www.imgur.com > green "New post" icon).

My concern being that the marketing images are being confused with installation/use instructions.

 

[demoncheg]

My concern being that the marketing images are being confused with installation/use instructions.

But the marketing image shows the correct processor. The lid mess up processor, removing it makes it impossible to install the chip in the socket.

 

[CountMike]

But the marketing image shows the correct processor. The lid mess up processor, removing it makes it impossible to install the chip in the socket.

That picture is just what's called "Artist's render" not an actual photo. You are taking it too literary

 

[demoncheg]

That picture is just what's called "Artist's render" not an actual photo. You are taking it too literary

The frame around the chip is needed to install the processor in the socket.

 

[rgd1101]

are you still thinking of your direct fan is better than having a heatsink?

 

[COLGeek]

The rendered CPU (above) is likely one that would soldered into a laptop's or one of the micro-mini-PC's motherboard socket. It would not be removable once installed.

Desktop CPUs, as others have pointed out, mount differently.

What is the point of this concern?

 

[demoncheg]

are you still thinking of your direct fan is better than having a heatsink?

What is the point of this concern?

The CPU temperature under load reaches 70 degrees. It can be cooled until the cores in home computers freeze.

 

[COLGeek]

The CPU temperature under load reaches 70 degrees. It can be cooled until the cores in home computers freeze.

Back up. What are you talking about. Is this your previous cooler design? If so, what is your point?

Explain by using words and pictures.

 

[rgd1101]

is a mobile cpu. they can run to 100°C

 

[CountMike]

The frame around the chip is needed to install the processor in the socket.

That's an Intel CPU. Desktop Ryzen are held on all sides and corners. Ryzen H suffix CPUs are meant for portable devices, soldered to MB and likely direct die cooling without IHS. Still don't see what it has to do with with artist's rendered picture of possible innards. That's like comparing comics to photos.

 

[logainofhades]

The CPU temperature under load reaches 70 degrees. It can be cooled until the cores in home computers freeze.

70 is not that high these days. Modern chips are like 95c+ for max temps.

 

[demoncheg]

70 is not that high these days. Modern chips are like 95c+ for max temps.

But need to reach the minimum temperature to increase the core frequency.

 

[logainofhades]

But need to reach the minimum temperature to increase the core frequency.

You will never hit max frequency on a multi core workload. Max frequency is single core only.

 

[DSzymborski]

Is there an actual question here? This is like your third thread of stream-of-consciousness cooler thoughts.

 

[rgd1101]

But need to reach the minimum temperature to increase the core frequency.

there is no min temp for increase frequency that I know of. there are max temp that will decrease the core frequency

 

[CountMike]

But need to reach the minimum temperature to increase the core frequency.

No such thing, only maximum temperature at which it may slow down. Tjmax is published for all CPUs. Unless manually overclocking you would not get 1Hz over with any temperature bellow Tjmax. Only performance related issue my be occasional short temperature peaks over Tjmax that fails to be detected by SW and FW. As that's built into CPU microcode it can't be bypassed by any settings in BIOS.

 

[demoncheg]

Tjmax is published for all CPUs.

The processor is designed to function at Tjmax, but need Tjmin.

 

[CountMike]

The processor is designed to function at Tjmax, but need Tjmin.

Tjmin. is for stability and response time.