Question XMP/Higher Freq instability after mounting CPU

[AlphaTheWalf]

I'm relatively new to using XMP and overclocking memory at such high frequencies. I built my PC a few weeks ago and successfully got it functioning at 7600 MT/s using XMP without any issues. However, after swapping my mounting bracket, I encountered major problems with BitLocker and XMP when I restarted my PC. To resolve this, I performed a full Windows reset, reflashed the BIOS, cleared the CMOS, and updated the motherboard drivers, including the chipset. I've also reseated the memory, but I don't know why memory could get affected like this from a CPU Mounting Bracket Change, the CPU was reseated when I first did it.

At the moment, I have my memory manually set to 6800 MHz in the BIOS with everything on auto, and I'm trying to keep it stable for now. I ran Windows Memory Diagnostic and MemTest86 without any errors at 6800 MHz. However, as soon as I attempt to increase the memory speed to 7600 MHz, it fails to boot and shows numerous errors. Additionally, when trying speeds between 7000 MHz and 7400 MHz, I experience instability and frequent BSODs with memory errors.

If anyone has experience with these issues, I would appreciate any advice or relevant information.

Mem is in A2 B2

System Specs
CPU: Intel Core i9-13900K 3 GHz 24-Core Processor
Motherboard: Asus ROG STRIX Z790-E GAMING WIFI II ATX LGA1700 Motherboard
Memory: G.Skill Trident Z5 RGB 32 GB (2 x 16 GB) DDR5-7600 CL36
Storage: Samsung 980 Pro 1 TB M.2-2280 PCIe 4.0 x4 NVMe Solid State Drive
OS: Microsoft Windows 11 Pro

 

[AlphaTheWalf]

Bios Version: 1801
Intel Chipset Driver: 10.1.19600.8418

 

[reyna789]

Even though a CPU bracket change shouldn't directly affect RAM, it might have slightly disturbed the modules. Check RAM compatibility, reseat modules, test them individually, and adjust DRAM timings. Monitor temperatures. If issues persist, there might be a motherboard or CPU issue. Proceed with caution and consult resources for advanced troubleshooting.

 

[Bob.B]

I'm relatively new to using XMP and overclocking memory at such high frequencies. I built my PC a few weeks ago and successfully got it functioning at 7600 MT/s using XMP without any issues. However, after swapping my mounting bracket, I encountered major problems with BitLocker and XMP when I restarted my PC. To resolve this, I performed a full Windows reset, reflashed the BIOS, cleared the CMOS, and updated the motherboard drivers, including the chipset. I've also reseated the memory, but I don't know why memory could get affected like this from a CPU Mounting Bracket Change, the CPU was reseated when I first did it.

At the moment, I have my memory manually set to 6800 MHz in the BIOS with everything on auto, and I'm trying to keep it stable for now. I ran Windows Memory Diagnostic and MemTest86 without any errors at 6800 MHz. However, as soon as I attempt to increase the memory speed to 7600 MHz, it fails to boot and shows numerous errors. Additionally, when trying speeds between 7000 MHz and 7400 MHz, I experience instability and frequent BSODs with memory errors.

If anyone has experience with these issues, I would appreciate any advice or relevant information.

Mem is in A2 B2

System Specs
CPU: Intel Core i9-13900K 3 GHz 24-Core Processor
Motherboard: Asus ROG STRIX Z790-E GAMING WIFI II ATX LGA1700 Motherboard
Memory: G.Skill Trident Z5 RGB 32 GB (2 x 16 GB) DDR5-7600 CL36
Storage: Samsung 980 Pro 1 TB M.2-2280 PCIe 4.0 x4 NVMe Solid State Drive
OS: Microsoft Windows 11 Pro

Play with the cpu heatsink mounting pressure see if it make a diff.